Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087984 INTERIOR PANELS / TRIM _0420190 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


PROCEDURE

Hide 55328 1.INSTALL NO. 1 INSTRUMENT PANEL PIN (for Separate Type)

HINT:

Use the same procedure as for the opposite side.


a.

Engage the guide.


b.

Install the No. 1 instrument panel pin with the screw.


Hide 89120A 2.INSTALL AUTOMATIC LIGHT CONTROL SENSOR (for Separate Type)

Hide 55950G 3.INSTALL DEFROSTER NOZZLE ASSEMBLY (for Separate Type)

a.
B587166E01
0.063,1.177 0.354,1.354 0.292,0.177 10 true <A> 1.313,1.417 1.604,1.594 0.292,0.177 10 true <A> 3.073,1.406 3.365,1.583 0.292,0.177 10 true <A>

Engage the guides.


b.

Install the defroster nozzle assembly with the 3 screws <A>.


Hide 55302C 4.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for Integrated Type)

a.

When installing a new instrument panel sub-assembly:

i.
B576412C01
1.604,1.5 1.781,1.313 false 1.396,1.708 1.792,1.927 1.792,1.927 2.198,1.708 false 1.802,1.208 2.115,1.406 0.313,0.198 10 false *a 1.74,1.958 2.052,2.125 0.313,0.167 10 false *b
*a Runner Portion
*b Cut Off


Using a nipper, cut off both ends of the runner portion as shown in the illustration.



b.

Engage the guides to install the instrument panel sub-assembly as shown in the illustration.

B580442C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)



c.

Install the 3 bolts <F>, screw <E> and nut <I> as shown in the illustration.

B579333C01
1.198,2.375 1.51,2.188 true 2.021,2.375 1.719,2.177 true 0.896,1.5 0.76,1.354 true 0.948,1.448 1.135,1.615 0.188,0.167 10 true *a 1.479,2.083 1.719,2.26 0.24,0.177 10 true *b 4.76,0.917 5.094,1.094 0.333,0.177 10 true <H> 5.229,1.698 5.479,1.875 0.25,0.177 10 true <I> 6.49,2.271 6.781,2.438 0.292,0.167 10 true <F> 4.385,2.5 4.677,2.677 0.292,0.177 10 true <F> 2.51,2.625 2.813,2.792 0.302,0.167 10 true <E> 1.948,2.604 2.25,2.781 0.302,0.177 10 true <G> 1.125,2.594 1.458,2.771 0.333,0.177 10 true <G> 0.344,2.292 0.656,2.469 0.313,0.177 10 true <F>
*a Airbag Connector *b Airbag Bolt



d.

Engage the hooks.


e.

Install the 4 clips.


f.

Connect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



g.

Install the 2 bolts <G>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


h.

Engage the guide and install the ground bracket with the bolt <H>.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Connect the connector.


Hide 55302C 5.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for Separate Type)

a.

When installing a new instrument panel sub-assembly:

i.
B592282C01
1.552,1.49 1.781,1.313 false 1.219,1.729 1.615,1.896 1.615,1.896 2.021,1.698 false 1.844,1.188 2.156,1.385 0.313,0.198 10 false *a 1.615,1.958 1.938,2.135 0.323,0.177 10 false *b
*a Runner Portion
*b Cut Off


Using a nipper, cut off both ends of the runner portion as shown in the illustration.



b.

Engage the guides to install the instrument panel sub-assembly as shown in the illustration.

B592283C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)



c.

Install the 5 bolts <F>, screw <E> and nut <I> as shown in the illustration.

B592285C01
5.125,2.365 5.438,2.177 true 5.958,2.365 5.656,2.167 true 6.146,1.49 6.229,1.365 true 6.021,1.479 6.219,1.646 0.198,0.167 10 true *a 5.427,2.031 5.667,2.208 0.24,0.177 10 true *b 3.177,0.969 3.5,1.135 0.323,0.167 10 true <H> 1.813,1.76 2.115,1.969 0.302,0.208 10 true <I> 6.531,2.292 6.844,2.469 0.313,0.177 10 true <F> 2.708,2.646 2.99,2.802 0.281,0.156 10 true <F> 4.333,2.781 4.635,2.948 0.302,0.167 10 true <E> 5.99,2.667 6.302,2.833 0.313,0.167 10 true <G> 5.271,2.635 5.563,2.833 0.292,0.198 10 true <G> 0.385,2.281 0.677,2.458 0.292,0.177 10 true <F> 4.333,0.26 4.667,0.458 0.333,0.198 10 false <F> 1.844,1.031 2.135,1.208 0.292,0.177 10 true <F>
*a Airbag Connector *b Airbag Bolt



d.

Engage the hooks.


e.

Install the 4 clips.


f.

Connect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



g.

Install the 2 bolts <G>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


h.

Engage the guide and install the ground bracket with the bolt <H>.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Connect the connector.


Hide 86160L 6.INSTALL FRONT NO.4 SPEAKER ASSEMBLY (for 8 Speakers)

Hide 55313A 7.INSTALL INSTRUMENT MAIN PANEL (for Separate Type)

a.

Engage the guides as shown in the illustration.

B592286C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Connect the connector.


c.

Engage the clips and claws to install the instrument main panel as shown in the illustration.

B596159C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 86160J 8.INSTALL FRONT NO.3 SPEAKER ASSEMBLY (w/ Telematics Transceiver)

Hide 55510F 9.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY (w/ Telematics Transceiver)

B595532

a.

Engage the 4 clips to install the No. 1 speaker opening cover assembly as shown in the illustration.


Hide 55408F 10.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 8 Speakers)

B595533C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


a.

Engage the 5 claws and 2 guides to install the No. 1 instrument panel speaker sub-assembly as shown in the illustration.


Hide 55409F 11.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 8 Speakers)

HINT:

Use the same procedure as for the No. 1 side.


Hide 55414A 12.INSTALL INSTRUMENT CLUSTER FINISH END PANEL (w/ Headup Display)

a.
B596160C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides and claws to install the instrument cluster finish end panel as shown in the illustration.


Hide 55624A 13.INSTALL INSTRUMENT PANEL CENTER TRAY

a.
B596161C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the instrument panel center tray as shown in the illustration.


Hide 55420A 14.INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY

a.
B596162C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the instrument cluster finish center panel assembly as shown in the illustration.


Hide 86140A 15.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Audio)

Hide 55670A 16.INSTALL INSTRUMENT PANEL CENTER REGISTER ASSEMBLY

a.

Engage the clamp.


b.
B596163C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and clips to install the instrument panel center register assembly as shown in the illustration.


Hide 55405B 17.INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY

a.

Connect the connector.


b.
B596164C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, clips and claws to install the instrument cluster finish center panel sub-assembly as shown in the illustration.


Hide 55406B 18.INSTALL INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 19.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 83100 20.INSTALL COMBINATION METER ASSEMBLY (for Analog Meter)

Hide 83100 21.INSTALL COMBINATION METER ASSEMBLY (for Digital Meter)

Hide 55410C 22.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Analog Meter)

a.
B596165C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, clips and claws to install the instrument cluster finish panel assembly as shown in the illustration.


b.

Install the 2 screws <A> or 2 screws <B>.


Hide 55410C 23.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Digital Meter)

a.
B596166C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, clips and claws to install the instrument cluster finish panel assembly as shown in the illustration.


b.

Install the 2 screws <A> or 2 screws <B>.


Hide 55548A 24.INSTALL INSTRUMENT PANEL HOLE COVER (w/ Cover)

a.
B574305E03
0.333,0.635 0.625,0.802 0.292,0.167 10 true <A> 2.76,1.5 3.052,1.667 0.292,0.167 10 true <A>

Engage the guides.


b.

Install the instrument panel hole cover with the 2 screws <A>.


Hide 55480D 25.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.

Connect each connector.


b.
B596168C01
0.542,1.854 0.844,2.021 0.302,0.167 10 true <F>
V113147

Install in this Direction


Engage the guide, clips and claw to install the lower instrument panel finish panel assembly as shown in the illustration.


c.

Install the bolt <F>.


Hide 53601 26.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B596169

Engage the guides and claw to connect the hood lock control lever sub-assembly.


Hide 86160P 27.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for 6 or 8 Speakers)

Hide 62212 28.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the adhesive tape and protective cover.


b.
B596170C01
0,0 0,0 false

Install a new front pillar garnish clips to the front pillar garnish LH.

NOTICE:

When installing the front pillar garnish clip, make sure to install it in the correct position and facing in the correct direction.



c.
B596171C01
0,0 0,0 false

w/ Speaker:

i.

Engage the claws to connect the front No.2 speaker assembly.



d.

w/o Speaker:

i.

Engage the clamp.



e.
B597706C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the locations shown in the illustration.


f.
B597707C01
0,0 0,0 false
V113147

Install in this Direction


Align the guides and partially engage the front pillar garnish LH.


g.
B597708C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


While holding down the tip of the front pillar garnish LH, push it in as shown in the illustration.


h.
B597709C01
0,0 0,0 false
V113147

Install in this Direction


Engage the front pillar garnish clip and clip to install the front pillar garnish LH as shown in the illustration.


Hide 62211 29.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 55557A 30.INSTALL GLOVE COMPARTMENT DOOR CHECK CUSHION

HINT:

Use the same procedure as for the opposite side.


a.
B596174

Engage the claws to install the glove compartment door check cushion.


Hide 55433B 31.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

a.
B596175C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and claws to install the lower No. 2 instrument panel finish panel as shown in the illustration.


b.
B596176E01
0.25,1.448 0.563,1.625 0.313,0.177 10 true <D> 1.854,0.635 2.167,0.813 0.313,0.177 10 true <E> 0.948,0.667 1.26,0.844 0.313,0.177 10 true <C> 2.813,0.146 3.125,0.323 0.313,0.177 10 true <D> 0.135,0.104 0.448,0.281 0.313,0.177 10 true <D> 3.073,1.802 3.385,1.979 0.313,0.177 10 true <C>

Install the 2 screws <C>, 3 screws <D> and screw <E>.


Hide 55054 32.INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.

Engage the claw to install the glove compartment door stopper sub-assembly.


Hide 55550 33.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B596177C01
0,0 0,0 false
V113147

Install in this Direction


Engage the hinges in the horizontal direction to install the glove compartment door assembly as shown in the illustration.

NOTICE:
·

Engaging the hinges from the top will deform the hinges.

·

Be sure to install the glove compartment door assembly horizontally.




b.

Eengage the claw to install the glove compartment door stopper sub-assembly from the glove compartment door assembly.


c.
B596178C01
2.698,0.927 2.969,0.604 true 0.688,0.771 0.469,0.469 true 0.24,0.365 0.458,0.552 0.219,0.188 10 true *a 2.969,0.51 3.188,0.698 0.219,0.188 10 true *a
*a Stopper
V100135

Push


While pushing in the sides of the glove compartment door assembly as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.


Hide 55317E 34.INSTALL NO. 1 INSTRUMENT SIDE PANEL

a.

for Front Passenger Side with Airbag Cut off Switch:

i.

Connect the connector.



b.
B596179C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides and clips to install the No. 1 instrument side panel as shown in the illustration.


Hide 55318F 35.INSTALL NO. 2 INSTRUMENT SIDE PANEL

HINT:

Use the same procedure as for the RH side.


Hide 62312B 36.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Connect the front door opening trim weatherstrip LH.


Hide 62311B 37.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 55607 38.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B596180C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide and claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.


Hide 55606 39.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B596181C01
0.177,0.813 0.479,0.99 0.302,0.177 10 true <A> 3.042,0.375 3.344,0.552 0.302,0.177 10 true <A>
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guide and claws as shown in the illustration.


b.

Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <A>.


Hide 62112 40.INSTALL COWL SIDE TRIM BOARD LH

Hide 62111C 41.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67914B 42.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67913B 43.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 44.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 45.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 46.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 47. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART