Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C05621C  Brake Pedal Position Sensor Supply Voltage Circuit Voltage Out of Range  C124B00  Stroke Sensor Data Invalid  C139251  Zero Point Calibration of Stroke Sensor Not Programmed  P057A12  Brake Pedal Position Sensor "A" Circuit Short to Battery  P057A14  Brake Pedal Position Sensor "A" Circuit Short to Ground or Open  P057A1F  Brake Pedal Position Sensor "A" Circuit Intermittent  P05DB12  Brake Pedal Position Sensor "B" Circuit Short to Battery  P05DB14  Brake Pedal Position Sensor "B" Circuit Short to Ground or Open  P05DB1F  Brake Pedal Position Sensor "B" Circuit Intermittent  P05E062  Brake Pedal Position Sensor "A"/"B" Signal Compare Failure  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C05621C Brake Pedal Position Sensor Supply Voltage Circuit Voltage Out of Range The sensor supply voltage (VCSK) is 4.7 V or less, or 5.3 V or more for 0.2 seconds or more.
·

Open or short in brake pedal stroke sensor assembly power supply circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (brake booster with master cylinder assembly)


Brake
C124B00 Stroke Sensor Data Invalid Sensor data is invalid for 0.2 seconds or more. (The sensor data of SKS1 and SKS2 is invalid.)
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
C139251 Zero Point Calibration of Stroke Sensor Not Programmed The brake pedal stroke sensor assembly zero point calibration is not performed. (Normal brake pedal stroke sensor assembly zero point not memorized.) Normal brake pedal stroke sensor assembly zero point not memorized. (Linear solenoid valve offset learning is not performed or Dealer Mode is not performed or not complete.) Brake
P057A12 Brake Pedal Position Sensor "A" Circuit Short to Battery The sensor output voltage 1 (SKS1) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
P057A14 Brake Pedal Position Sensor "A" Circuit Short to Ground or Open The sensor output voltage 1 (SKS1) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
P057A1F Brake Pedal Position Sensor "A" Circuit Intermittent The difference between the current value and previous value of the sensor output voltage 1 (SKS1) is 8.5% or more for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
P05DB12 Brake Pedal Position Sensor "B" Circuit Short to Battery The sensor output voltage 2 (SKS2) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
P05DB14 Brake Pedal Position Sensor "B" Circuit Short to Ground or Open The sensor output voltage 2 (SKS2) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
P05DB1F Brake Pedal Position Sensor "B" Circuit Intermittent The difference between the current value and previous value of the sensor output voltage 2 (SKS2) is 8.5% or more for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake
P05E062 Brake Pedal Position Sensor "A"/"B" Signal Compare Failure The difference in change between sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) is excessively large for 0.2 seconds or more. (The comparison value of SKS1 and SKS2 is invalid.)
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


Brake

WIRING DIAGRAM

C345754E23
4.646,0.552 4.958,0.75 0.313,0.198 10 false 25 4.917,0.771 5.385,1.01 0.469,0.24 10 false VSK1 4.656,1.167 4.969,1.365 0.313,0.198 10 false 17 4.927,1.385 5.385,1.615 0.458,0.229 10 false SKS1 4.646,1.781 4.958,1.979 0.313,0.198 10 false 13 4.906,2 5.406,2.292 0.5,0.292 10 false SKG1 4.656,2.292 4.969,2.49 0.313,0.198 10 false 21 4.906,2.521 5.385,2.781 0.479,0.26 10 false VSK2 4.646,2.917 4.958,3.115 0.313,0.198 10 false 19 4.896,3.125 5.365,3.396 0.469,0.271 10 false SKS2 4.646,3.521 4.958,3.719 0.313,0.198 10 false 33 4.896,3.74 5.417,4.021 0.521,0.281 10 false SKG2 6.375,2.104 6.688,2.302 0.313,0.198 10 false IC 4.813,4.094 5.125,4.292 0.313,0.198 10 false A38 4.823,4.26 6.885,4.656 2.063,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.865,0.563 3.177,0.76 0.313,0.198 10 false 4 2.865,1.177 3.177,1.375 0.313,0.198 10 false 6 2.865,1.792 3.177,1.99 0.313,0.198 10 false 5 2.865,2.302 3.177,2.5 0.313,0.198 10 false 2 2.865,2.927 3.177,3.125 0.313,0.198 10 false 1 2.865,3.531 3.177,3.729 0.313,0.198 10 false 3 0.458,4.104 0.771,4.302 0.313,0.198 10 false A27 0.458,4.281 2.917,4.646 2.458,0.365 10 false Brake Pedal Stroke Sensor Assembly 0.74,1.198 0.99,1.531 0.25,0.333 10 false Hall IC1 0.74,2.938 1,3.344 0.26,0.406 10 false Hall IC2 2.375,0.771 2.844,1.01 0.469,0.24 10 false VCSK 2.417,1.396 2.875,1.625 0.458,0.229 10 false SKS1 2.458,2 2.958,2.292 0.5,0.292 10 false SKG 2.396,2.51 2.875,2.771 0.479,0.26 10 false VSK2 2.396,3.135 2.865,3.406 0.469,0.271 10 false SKS2 2.385,3.76 2.906,4.042 0.521,0.281 10 false SKG2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for HV Model RHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C139251 is output A
DTCs C05621C, C124B00, C139251, P057A12, P057A14, P057A1F, P05DB12, P05DB14, P05DB1F or P05E062 is output B
None of the above conditions are met C



A

3.SYSTEM INFORMATION MEMORIZATION

B

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)

C

GO TO DTC CHART

3.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Use the GTS, clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C139251 is output A
DTCs are not output B
None of the above conditions are met C



A

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

B

C

GO TO DTC CHART

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-4 (VCSK) - A27-5 (SKG) Ignition switch ON 4.84 to 5.16 V
A27-2 (VSK2) - A27-3 (SKG2) Ignition switch ON 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A27 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-13 (SKG1) - A27-5 (SKG) Always Below 1 Ω
A38-13 (SKG1) or A27-5 (SKG) - Body ground Always 10 kΩ or higher
A38-17 (SKS1) - A27-6 (SKS1) Always Below 1 Ω
A38-17 (SKS1) or A27-6 (SKS1) - Body ground Always 10 kΩ or higher
A38-19 (SKS2) - A27-1 (SKS2) Always Below 1 Ω
A38-19 (SKS2) or A27-1 (SKS2) - Body ground Always 10 kΩ or higher
A38-21 (VSK2) - A27-2 (VSK2) Always Below 1 Ω
A38-21 (VSK2) or A27-2 (VSK2) - Body ground Always 10 kΩ or higher
A38-25 (VSK1) - A27-4 (VCSK) Always Below 1 Ω
A38-25 (VSK1) or A27-4 (VCSK) - Body ground Always 10 kΩ or higher
A38-33 (SKG2) - A27-3 (SKG2) Always Below 1 Ω
A38-33 (SKG2) or A27-3 (SKG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-4 (VCSK) - A27-5 (SKG) Ignition switch ON 4.84 to 5.16 V
A27-2 (VSK2) - A27-3 (SKG2) Ignition switch ON 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY