1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
89510D
2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY (for TMC Made)
When installing a new brake pedal stroke sensor assembly:
Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.
| *a | Brake Pedal Stroke Sensor Assembly Lever |
| *b | Brake Pedal Groove |
| *c | Brake Pedal Stroke Sensor Assembly Lever Set Pin |
Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.
Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.
Do not drop the brake pedal stroke sensor assembly.
If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.
Connect the connector.
Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin.
Remove the broken lever set pin.
When reusing the brake pedal stroke sensor assembly:
| *a | Brake Pedal Stroke Sensor Assembly Lever |
| *b | Brake Pedal Groove |
Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 nuts.
Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.
Do not drop the brake pedal stroke sensor assembly.
If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.
Connect the connector.
89510D
3.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY (for TMMF Made)
When installing a new brake pedal stroke sensor assembly:
| *a | Locking Plate |
Until the brake pedal stroke sensor assembly has been installed to the brake pedal support assembly with the nut, do not press in the brake pedal stroke sensor lever locking plate.
When the brake pedal stroke sensor assembly has been tightened to the specified torque, the locking plate will be released.
| *a | Brake Pedal Stroke Sensor Assembly Lever |
| *b | Brake Pedal Groove |
Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.
Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.
Do not drop the brake pedal stroke sensor assembly.
If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.
Connect the connector.
When reusing the brake pedal stroke sensor assembly:
| *a | Brake Pedal Stroke Sensor Assembly Lever |
| *b | Brake Pedal Groove |
Install brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.
Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.
Do not drop the brake pedal stroke sensor assembly.
If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.
Connect the connector.
4.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
89510D
5.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY (for TMC Made)
When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.
Connect the GTS to the DLC3 with the ignition switch off.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Brake / Data List / Stroke Sensor.
| Tester Display |
|---|
| Stroke Sensor |
Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.
0.8 to 1.2 V
Tighten the 2 nuts.
Do not depress the brake pedal after turning the ignition switch to ON.
Turn the GTS off and turn the ignition switch off.
Disconnect the GTS from the DLC3.
87211
6.INSTALL NO. 1 AIR DUCT
55606
7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
8. PERFORM INITIALIZATION AND CALIBRATION
9.CHECK AND CLEAR DTC
10. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART