The skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.
If the auxiliary battery voltage is temporarily low, these DTCs may be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C059400 | Brake Booster Motor "A" Performance | The pump motor is operating continuously for 178 seconds or more. (When the relay is malfunctioning for 98 seconds or more.) | ·
Short in pump motor circuit or pump motor monitor circuit ·
Motor relay stuck ·
Accumulator pressure sensor malfunction ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| C121B14 | Brake Booster Motor "A" Control "A" Circuit Short to Ground or Open | An open is detected in the motor relay drive circuit for 0.2 seconds or more. | ·
Open in pump motor circuit or pump motor monitor circuit ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| C126A14 | Brake Booster Motor "A" Control "B" Circuit Short to Ground or Open | An open is detected in the motor relay drive circuit for 0.2 seconds or more. | ·
Open in pump motor circuit or pump motor monitor circuit ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| C141C12 | Brake Booster Motor "A" Control Circuit Short to Battery | A short is detected in the motor relay drive circuit for 2 seconds or more. | ·
Short in pump motor circuit or pump motor monitor circuit ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| C141C14 | Brake Booster Motor "A" Control Circuit Short to Ground or Open | An open is detected in the motor relay drive circuit for 0.2 seconds or more. | ·
Open in pump motor circuit or pump motor monitor circuit ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Check the DTCs that are output.
| Result | Proceed to |
|---|---|
| C059400, C121B14, C126A14, C141C12 or C141C14 is output | A |
| C059400, C121B14, C126A14, C141C12 or C141C14 and other DTCs are output | B |
A
B
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| Tester Display |
|---|
| MTT |
Depress the brake pedal several times and check the operation status of the MTT.
Depressing the brake pedal several times drops the accumulator pressure and operates the pump motor.
| Result | Proceed to |
|---|---|
| The MTT in the Data List turns on or off by depressing the brake pedal several times. | A |
| The status of MTT in the Data List does not change even after depressing the brake pedal several times. | B |
A
B
| *a | Component without harness connected
(Brake Booster Pump Assembly) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A30 brake booster pump assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (BM1) - 4 (GND1) | Always | 10 Ω or less |
| 1 (BM2) - 3 (GND2) | Always | 10 Ω or less |
| 2 (BM1) - 1 (BM2) | Always | Below 1 Ω |
| 4 (GND1) - 3 (GND2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-4 (GND1) - Body ground | Always | Below 1 Ω |
| A30-3 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A30 brake booster pump assembly connector.
Disconnect the A27 brake pedal stroke sensor assembly connector.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa, Max.: 24.48 MPa | 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped) |
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Tester Display |
|---|
| MTT |
| Accumulator Pressure |
Depress the brake pedal several times to operate the pump motor, then wait until it stops.
After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.
This inspection checks whether an accumulator pressure sensor malfunction, internal brake actuator (brake booster with master cylinder assembly) leak or prolonged operation due to detection of low pressure caused by accumulator deterioration, caused the DTC to be stored.
If the brake fluid level in the brake master cylinder reservoir assembly (brake booster with master cylinder assembly) drops, an external brake fluid leak is suspected.
| Result | Proceed to |
|---|---|
| 30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds | A |
| 30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds | B |
A
B
Turn the ignition switch off.
Reconnect the A27 brake pedal stroke sensor assembly connector.
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C059400, C121B14, C126A14, C141C12 and C141C14 are not output | A |
| C059400, C121B14, C126A14, C141C12 or C141C14 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Reconnect the A27 brake pedal stroke sensor assembly connector.
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB Solenoid (SLR) | Linear solenoid reduction valve (SLR) | Solenoid ON/OFF | ECB: Electronically Controlled Brake System |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa, Max.: 24.48 MPa | Brake pedal released: 0.00 to 1.53 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Active Test Display |
|---|
| ECB Solenoid (SLR) |
| Data List Display |
|---|
| Servo Pressure |
Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).
Check that the servo pressure output value does not increase when performing the Active Test.
The servo pressure output value does not increase when performing the Active Test.
If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.
| Result | Proceed to |
|---|---|
| The servo pressure output value increases. | A |
| The servo pressure output value does not increase. | B |
A
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-2 (MRI1) - Body ground | Always | 11 to 14 V |
| A38-28 (MRI2) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A30 brake booster pump assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-1 (MRO1) - A30-2 (BM1) | Always | Below 1 Ω |
| A38-1 (MRO1) or A30-2 (BM1) - Body ground | Always | 10 kΩ or higher |
| A38-27 (MRO2) - A30-1 (BM2) | Always | Below 1 Ω |
| A38-27 (MRO2) or A30-1 (BM2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG