Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C059704  Brake System Control Module "A" System Internal Failure  C142C14  BI2 Supply Circuit Short to Ground or Open  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores this DTC if malfunctions are found in the circuit inside the ECU by self-diagnosis.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C059704 Brake System Control Module "A" System Internal Failure Any of the following is detected:
·

Skid control ECU (brake booster with master cylinder assembly) internal malfunction.

·

Sudden drop of power source voltage or skid control ECU (brake booster with master cylinder assembly) internal malfunction.

·

An open is detected in the brake booster pump assembly circuit or skid control ECU (brake booster with master cylinder assembly) internal malfunction.


Skid control ECU (brake booster with master cylinder assembly) Brake
C142C14 BI2 Supply Circuit Short to Ground or Open Any of the following is detected:
·

An open is detected in the brake booster pump assembly circuit or skid control ECU (brake booster with master cylinder assembly) internal malfunction.

·

Skid control ECU (brake booster with master cylinder assembly) internal malfunction.


·

Auxiliary battery

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

WIRING DIAGRAM

C422547E15
4.521,5.656 4.979,5.854 0.458,0.198 10 false A38 4.51,5.844 6.854,6.469 2.344,0.625 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.156,7.365 6.906,7.781 1.75,0.417 10 false from Auxiliary Battery 3.292,4.552 4.667,4.833 1.375,0.281 10 false ABS MTR NO.2 3.271,3.854 4.583,4.083 1.313,0.229 10 false ABS MTR NO.1 4.365,3.542 4.823,3.74 0.458,0.198 10 false 2 4.313,4.271 4.771,4.469 0.458,0.198 10 false 28 4.615,3.813 5.073,4.01 0.458,0.198 10 false MRI1 4.604,4.531 5.063,4.729 0.458,0.198 10 false MRI2 4.833,2.417 5.354,2.823 0.521,0.406 10 false Motor Relay 6.417,2.135 6.875,2.333 0.458,0.198 10 false IC 4.333,1.344 4.792,1.542 0.458,0.198 10 false 27 4.604,1.594 5.063,1.792 0.458,0.198 10 false MRO2 4.375,0.51 4.833,0.708 0.458,0.198 10 false 1 4.615,0.75 5.073,0.948 0.458,0.198 10 false MRO1 1.083,0.75 1.542,0.948 0.458,0.198 10 false BM1 1.542,0.49 2,0.688 0.458,0.198 10 false 2 1.083,1.604 1.542,1.802 0.458,0.198 10 false BM2 1,6.115 1.458,6.313 0.458,0.198 10 false GND1 1.552,5.844 2.01,6.042 0.458,0.198 10 false 4 1,7.063 1.458,7.26 0.458,0.198 10 false GND2 1.552,6.813 2.01,7.01 0.458,0.198 10 false 3 1.563,1.333 2.021,1.531 0.458,0.198 10 false 1 0.083,8 0.542,8.198 0.458,0.198 10 false A30 0.063,8.177 1.417,8.719 1.354,0.542 10 false Brake Booster Pump Assembly 3.396,5.25 4.583,5.5 1.188,0.25 10 false ABS NO.3 4.615,5.198 5.073,5.396 0.458,0.198 10 false +BI2 4.375,4.958 4.833,5.156 0.458,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C059704 is output A
Only C142C14 is output B
None of the above conditions are met C



A

3.CHECK FREEZE FRAME DATA

B

8.CHECK AUXILIARY BATTERY

C

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK FREEZE FRAME DATA
a.

Using the GTS, read the "IGR Voltage Value", "IGP Voltage Value", "BS(linear) Voltage Value", "BS(ABS) Voltage Value", "VM1 Voltage Value" and "VM2 Voltage Value" of the Freeze Frame Data stored when the DTC C059704 was stored.

Chassis > Brake > Trouble Codes
50001 435
Result:
Result Proceed to
The value of any IGR Voltage Value, IGP Voltage Value, BS(linear) Voltage Value, BS(ABS) Voltage Value, VM1 Voltage Value, VM2 Voltage Value is 7.00 V or less A
The value of all IGR Voltage Value, IGP Voltage Value, BS(linear) Voltage Value, BS(ABS) Voltage Value, VM1 Voltage Value, VM2 Voltage Value is 12.00 V or more B


HINT:

If any of the voltage values of the Freeze Frame Data are 7.00 V or less, a sudden drop of the power source voltage is suspected as a cause of the DTC output.

In this case, inspect the auxiliary battery and replace or recharge the auxiliary battery as necessary.




A

4.CHECK AUXILIARY BATTERY

B

5.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Ignition switch ON 11 to 14 V
Auxiliary battery Ignition switch ON (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

END

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
C345125C39
0.698,1.333 1.448,1.656 true 1.99,1.604 2.74,1.302 true 2.01,2.125 2.719,2.656 true 0.729,2.625 1.427,2.135 true 0.208,0.198 0.521,0.396 0.313,0.198 10 false *a 0.385,1.229 0.698,1.427 0.313,0.198 10 false BM1 0.323,2.563 0.75,2.792 0.427,0.229 10 false GND1 2.75,2.594 3.188,2.854 0.438,0.26 10 false GND2 2.792,1.188 3.188,1.406 0.396,0.219 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A30 brake booster pump assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always 10 Ω or less
1 (BM2) - 3 (GND2) Always 10 Ω or less
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-4 (GND1) - Body ground Always Below 1 Ω
A30-3 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-1 (MRO1) - A30-2 (BM1) Always Below 1 Ω
A38-1 (MRO1) or A30-2 (BM1) - Body ground Always 10 kΩ or higher
A38-27 (MRO2) - A30-1 (BM2) Always Below 1 Ω
A38-27 (MRO2) or A30-1 (BM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Ignition switch ON 11 to 14 V
Auxiliary battery Ignition switch ON (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (+BI2 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

9.CHECK HARNESS AND CONNECTOR (+BI2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-5 (+BI2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR