Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C12C017  Brake System Control Module Power Supply Voltage Circuit Voltage Above Threshold  


DESCRIPTION

If a malfunction is detected in the power source circuit, the skid control ECU (brake booster with master cylinder assembly) stores DTC C12C017 and prohibits operation of ABS, brake assist, regenerative brake cooperative control, etc.

DTC C12C017 is stored if an excessive ECU voltage due to a malfunction in the auxiliary battery, charging circuit, etc. is detected, and is cleared when the ECU voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C12C017 Brake System Control Module Power Supply Voltage Circuit Voltage Above Threshold The internal voltage of the skid control ECU (brake booster with master cylinder assembly) is 16.44 V or more for 0.8 seconds or more.
·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Wire harness or connector

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Ignition switch ON 11 to 14 V
Auxiliary battery Ignition switch ON (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-15 (+BI1) - Body ground Always 11 to 14 V
A38-5 (+BI2) - Body ground Always 11 to 14 V
A38-52 (BS) - Body ground Always 11 to 14 V
A38-23 (IGR) - Body ground Ignition switch ON 11 to 14 V
A38-9 (IGP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CLEAR DTC
a.

Turn the ignition switch off.


b.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C12C017 is not output A
C12C017 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY