The main relay supplies power to the switching solenoid and the linear solenoid.
The main relay remains on for approximately 2 minutes after the ignition switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C12F812 | ECB Solenoid Control "A" Circuit Short to Battery | The BS terminal voltage is 3.5 V or more for 4.5 seconds or more, when operation of the main relay is requested. | ·
Short in main relay circuit ·
Main relay internal stuck ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| C12F814 | ECB Solenoid Control "A" Circuit Short to Ground or Open | ·
When the ignition switch ON (READY): The BS terminal voltage is less than 3.5 V for 0.05 seconds or more, when the IGR terminal voltage is 9.5 V or more and operation of the main relay is requested. ·
When the ignition switch is off: The BS terminal voltage is less than 3.5 V for 0.05 seconds or more, when operation of the main relay is requested. |
·
Open or short in main relay circuit ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
Refer to DTC C12C014.
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Inspect the fuses for circuits related to this system before performing the following procedure.
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB Main Relay | Main relay | Relay ON/OFF | ECB: Electronically Controlled Brake System |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ECB Main Relay | Main relay operation request | ON or OFF | ON: Relay on
OFF: Relay off |
ECB: Electronically Controlled Brake System |
| Active Test Display |
|---|
| ECB Main Relay |
| Data List Display |
|---|
| ECB Main Relay |
Check that the condition of the main relay observed on the GTS changes according to GTS operation.
| Result | Proceed to |
|---|---|
| ECB main relay in the Data List turns ON/OFF using the Active Test. | A |
| ECB main relay in the Data List does not change using the Active Test. | B |
A
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-52 (BS) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C12F812 and C12F814 are not output | A |
| C12F812 or C12F814 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-15 (+BI1) - Body ground | Always | 11 to 14 V |
| A38-5 (+BI2) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-52 (BS) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG