Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C139100  Abnormal Leak in Accumulator  


DESCRIPTION

This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C139100 Abnormal Leak in Accumulator Either of the following is detected:
·

When the brake pedal is not depressed and the pump motor is operating, the accumulator pressure sensor value does not increase a certain number of times.

·

When the brake pedal is not depressed and the pump motor is not operating, the accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times.


·

Brake fluid leaks

·

Brake actuator (brake booster with master cylinder assembly)

(Malfunctioning internal seal etc.)

·

Brake booster pump assembly

(Accumulator internal gas pressure decrease, etc.)


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (SERVO PRESSURE)
a.

Select the Active Test on the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid ON/OFF ECB: Electronically Controlled Brake System

b.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 435 42 210

c.

Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).


d.

Check that the servo pressure output value does not increase when performing the Active Test.

OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:

If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

2.CHECK OPERATING TIME OF PUMP MOTOR
2.CHECK OPERATING TIME OF PUMP MOTOR
a.

Turn the ignition switch to ON (READY).


b.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Chassis > Brake > Data List
Tester Display
MTT
50003 435 100

c.

With the ignition switch ON (READY), check the operation of the pump motor.

OK:

The pump motor operates once or more within 20 seconds or operates for 10 seconds or more each time.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR FLUID LEAK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK FOR FLUID LEAK
a.

Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model TMC Made)>BLEEDING



ii.

Turn the ignition switch off.


iii.

Disconnect the A27 brake pedal stroke sensor assembly connector.


iv.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake > Data List
Tester Display
MTT
Accumulator Pressure
50003 435 100,212

v.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


vi.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.



Result:
Result Proceed to
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds A
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER PUMP ASSEMBLY

for the brake booster with master cylinder assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model TMC Made RHD)>REMOVAL

for the brake booster pump assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL


B

MALFUNCTIONING PART