Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C14E914  Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTCs C05121F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>C05121F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C14E914 Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open Any of the following is detected:
·

The speed sensor power source voltage is low for 0.5 seconds or more.

·

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.


·

Skid control sensor wire RH

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake > Data List
Tester Display
RR Speed Open
50003 435 103

b.

Check for any momentary interruptions in the wire harness and connectors.

NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Result Proceed to
The value of RR Speed Open is always Normal A
The value of RR Speed Open outputs Error one or more times B



A

2.READ VALUE USING GTS (RR Wheel Speed)

B

5.INSPECT SKID CONTROL SENSOR WIRE RH
2.READ VALUE USING GTS (RR Wheel Speed)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
50003 435 15

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT SKID CONTROL SENSOR WIRE RH
3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C14E914 is not output A
C14E914 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.INSPECT SKID CONTROL SENSOR WIRE RH
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the i1 and iO1 skid control sensor wire RH connectors.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (RR+) - iO1-2 (RR+) Always Below 1 Ω
i1-2 (RR+) or iO1-2 (RR+) - Body ground and other terminals Always 10 kΩ or higher
i1-1 (RR-) - iO1-1 (RR-) Always Below 1 Ω
i1-1 (RR-) or iO1-1 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE RH)

NG

REPLACE SKID CONTROL SENSOR WIRE RH

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE RH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-7 (RR+) - iO1-2 (RR+) Always Below 1 Ω
A38-7 (RR+) or iO1-2 (RR+) - Body ground Always 10 kΩ or higher
A38-8 (RR-) - iO1-1 (RR-) Always Below 1 Ω
A38-8 (RR-) or iO1-1 (RR-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the iO1 skid control sensor wire RH connectors.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
iO1-2 (RR+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the rear speed sensor RH signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>TEST MODE PROCEDURE


HINT:

The rear speed sensor RH and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY