Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C00632A  Yaw Rate Sensor Signal Stuck In Range  C05201C  Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range  C05202A  Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range  C052096  Multi-axis Acceleration Sensor Module "A" Component Internal Failure  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

These DTCs are stored when the skid control ECU (brake actuator assembly) receives an internal malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly).

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U012587 are output. When DTCs U012587 are output together with C00632A, C05201C, C05202A and/or C052096, inspect and repair the trouble areas indicated by U012587 first.


DTCs may be stored if either of the following occurs:
·

Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.

·

Yaw rate and acceleration sensor (airbag sensor assembly) signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C00632A Yaw Rate Sensor Signal Stuck In Range A yaw rate sensor stuck malfunction status continues.
·

Yaw rate sensor (airbag sensor assembly) installation

·

Yaw rate sensor (airbag sensor assembly)


Brake
C05201C Multi-axis Acceleration Sensor Module "A" Circuit Voltage Out of Range At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed sensor exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)


Brake
C05202A Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range Any of the following is detected:
·

The acceleration sensor output value does not change 16 times or more as the vehicle speed drops from 30 km/h (19 mph) to 0 km/h (0 mph).

·

A GL1 stuck malfunction status continues.

·

A GL2 stuck malfunction status continues.


·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)


Brake
C052096 Multi-axis Acceleration Sensor Module "A" Component Internal Failure Either of the following is detected:
·

A data malfunction signal is received from the acceleration sensor.

·

Output values of GL1 and GL2 (front and rear, left and right) are outside permitted output range for 60 seconds or more.


·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:

If the yaw rate and acceleration sensor (airbag sensor assembly) was replaced or reinstalled, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.CHECK GTS OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Operate the GTS, and check for DTCs related to the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
Any CAN communication system relating DTCs are output A
None of the above conditions are met B



A

B

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

NG