The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).
When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C05061F | Right Front Wheel Speed Sensor Circuit Intermittent | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Front speed sensor RH ·
Speed sensor installation ·
Wire harness and connector ·
Front speed sensor rotor RH (front axle hub sub-assembly RH) ·
Skid control ECU (brake actuator assembly) |
Brake |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Tester Display |
|---|
| FR Speed Sensor Voltage Open |
Select the line graph display.
Check for any momentary interruption in the wire harness and connector.
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
Drive the vehicle and perform a road test.
Check the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the GTS to clear the codes.
Press the DTC clear button.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Operate the GTS to read the DTCs.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C05061F is not output | A |
| C05061F is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *1 | Front Speed Sensor RH |
| *a | Correct |
| *b | Incorrect |
| *c | 8.5 Nm |
| *d | No clearance |
Turn the ignition switch off.
Check the front speed sensor RH installation.
There is no clearance between the front speed sensor RH and steering knuckle.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front speed sensor RH and the component with the front speed sensor rotor RH.
for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMC Made)>REMOVAL
Check the front speed sensor RH tip and front speed sensor rotor RH.
No scratches, oil, or foreign matter on the front speed sensor RH tip and front speed sensor rotor RH.
If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.
If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.
Do not use parts cleaner when cleaning the front speed sensor rotor RH.
If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.
The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.
If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A36 skid control ECU (brake actuator assembly) connector.
Disconnect the A23 front speed sensor RH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-1 (FR+) - A36-31 (FR+) | Always | Below 1 Ω |
| A23-1 (FR+) or A36-31 (FR+) - Body ground | Always | 10 kΩ or higher |
| A23-2 (FR-) - A36-30 (FR-) | Always | Below 1 Ω |
| A23-2 (FR-) or A36-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A36 skid control ECU (brake actuator assembly) connector.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-1 (FR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG