The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).
When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C050C1F | Left Rear Wheel Speed Sensor Circuit Intermittent | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds. ·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more. |
·
Rear speed sensor LH (rear axle hub and bearing assembly LH) ·
Sensor installation ·
Skid control sensor wire LH ·
Wire harness and connector ·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) ·
Skid control ECU (brake actuator assembly) |
Brake |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Tester Display |
|---|
| RL Speed Sensor Voltage Open |
Select the line graph display.
Check for any momentary interruption in the wire harness and connector.
Normal (There are no momentary interruptions.)
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| RL Wheel Speed |
Drive the vehicle and perform a road test.
Check the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the GTS to clear the codes.
Press the DTC clear button.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Operate the GTS to read the DTCs.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C050C1F is not output | A |
| C050C1F is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Correct |
| *b | Incorrect |
| *c | No clearance |
Turn the ignition switch off.
Check the rear speed sensor LH installation.
There is no clearance between the rear speed sensor LH and the rear axle hub and bearing assembly LH.
The rear speed sensor rotor LH and rear speed sensor LH are incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor rotor LH needs to be replaced, replace the rear axle hub and bearing assembly LH with rear speed sensor LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the j1 and Oj1 skid control sensor wire LH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| j1-2 (RL+) - Oj1-1 (RL+) | Always | Below 1 Ω |
| j1-2 (RL+) or Oj1-1 (RL+) - Body ground and other terminals | Always | 10 kΩ or higher |
| j1-1 (RL-) - Oj1-3 (RL-) | Always | Below 1 Ω |
| j1-1 (RL-) or Oj1-3 (RL-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A36 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Oj1-1 (RL+) - A36-29 (RL+) | Always | Below 1 Ω |
| Oj1-1 (RL+) or A36-29 (RL+) - Body ground | Always | 10 kΩ or higher |
| Oj1-3 (RL-) - A36-28 (RL-) | Always | Below 1 Ω |
| Oj1-3 (RL-) or A36-28 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A36 skid control ECU (brake actuator assembly) connector.
Reconnect the Oj1 skid control sensor wire LH connector.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| j1-2 (RL+) - Body ground | Ignition switch ON | 11 to 14 V |
The rear speed sensor LH is incorporated into the rear axle hub and bearing assembly LH.
If the rear speed sensor LH needs to be replaced, replace the rear axle hub and bearing assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG