Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › 2020.07–2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  C121054  Yaw Rate Sensor Missing Calibration  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U012587 are output. When DTCs U012587 are output together with C051D54 and/or C121054, inspect and repair the trouble areas indicated by U012587 first.


These DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Zero point calibration of acceleration sensor undone.
·

Acceleration sensor zero point not calibrated

·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)


Brake
C121054 Yaw Rate Sensor Missing Calibration Zero point calibration of yaw rate sensor undone. Yaw rate sensor zero point not calibrated Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION



PROCEDURE

1.CHECK GTS OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Operate the GTS, and check for DTCs related to the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
Any CAN communication system relating DTCs are output A
None of the above conditions are met B



A

B

2.PERFORM CALIBRATION
2.PERFORM CALIBRATION
a.

Operate the GTS to perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check if the same DTC is output.


Result:
Result Proceed to
C051D54 and C121054 are not output A
C051D54 or C121054 is output B



A

END

B

5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (YAW RATE SENSOR VALUE)

NG

6.READ VALUE USING GTS (YAW RATE SENSOR VALUE)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake > Data List
Tester Display
Yaw Rate Sensor Value
50003 435 29

b.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The yaw rate sensor value is normal.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (LATERAL G)

NG

7.READ VALUE USING GTS (LATERAL G)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning:
Changes in proportion with lateral acceleration
Chassis > Brake > Data List
Tester Display
Lateral G
50003 435 25

b.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The lateral G value is normal.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FORWARD AND REARWARD G)

NG

8.READ VALUE USING GTS (FORWARD AND REARWARD G)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Forward and Rearward G Forward and Rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration:-25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration:
Changes in proportion with acceleration
Chassis > Brake > Data List
Tester Display
Forward and Rearward G
50003 435 26

b.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The forward and rearward G value is normal.



Result:
Proceed to
OK
NG



OK

NG