Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › 2020.07–2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  Brake Warning Light Remains ON  


DESCRIPTION

This procedure is for troubleshooting when the brake system warning light remains on but no DTCs are output.

The skid control ECU (brake actuator assembly) controls the brake system warning light in the combination meter assembly via CAN communication.

WIRING DIAGRAM

C427249E01
0.76,0.667 1.375,0.865 0.615,0.198 10 false CANL 0.75,1.26 1.365,1.458 0.615,0.198 10 false CANH 0.906,3.677 1.521,3.875 0.615,0.198 10 false SW 1.313,0.677 1.927,0.875 0.615,0.198 10 false H6 1.302,1.281 1.917,1.479 0.615,0.198 10 false H6 1.302,3.75 1.917,3.948 0.615,0.198 10 false H7 1.323,3.552 1.938,3.75 0.615,0.198 10 false 16 1.323,1.063 1.938,1.26 0.615,0.198 10 false 9 1.333,0.469 1.948,0.667 0.615,0.198 10 false 25 5.927,0.667 6.542,0.865 0.615,0.198 10 false CANL 5.927,1.26 6.542,1.458 0.615,0.198 10 false CANH 5.667,0.51 6.281,0.708 0.615,0.198 10 false 10 5.688,1.115 6.302,1.313 0.615,0.198 10 false 22 4.073,3.667 4.688,3.865 0.615,0.198 10 false 2 2.188,3.656 2.802,3.854 0.615,0.198 10 false 1 2.25,4.271 2.865,4.469 0.615,0.198 10 false A24 2.26,4.448 4.865,4.99 2.604,0.542 10 false Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 0.188,4.635 1.375,5.125 1.188,0.49 10 false Combination Meter Assembly 3.948,6.125 6.146,6.406 2.198,0.281 10 false : CAN Communication Line 5.531,4.74 7.063,5.281 1.531,0.542 10 false Skid Control ECU (Brake Actuator Assembly) 2.344,3.667 2.958,3.865 0.615,0.198 10 false + 3.875,3.656 4.49,3.854 0.615,0.198 10 false E 5.552,4.563 6.167,4.76 0.615,0.198 10 false A36

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.



PROCEDURE

1.PRE-CHECK
a.

Check that all of the following conditions required for the brake system warning light to turn off are met:

i.

The ABS warning light is not illuminated.

HINT:

If the ABS warning light remains illuminated, make sure that the conditions required for the ABS warning light to turn off are met.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>ABS Warning Light Remains ON



ii.

The brake fluid level in the brake master cylinder reservoir assembly is not low.


iii.

The vacuum inside the brake booster decreases.

HINT:

When the vacuum inside the brake booster decreases, the brake system warning light comes on.




Result:
Proceed to
NEXT



NEXT

2.CHECK GTS OUTPUT (CAN COMMUNICATION SYSTEM)
2.CHECK GTS OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Operate the GTS, and check for DTCs related to the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
Any CAN communication system relating DTCs are output A
None of the above conditions are met B



A

B

3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.

With a sufficient level of brake fluid, disconnect the A45 brake fluid level warning switch (brake master cylinder reservoir assembly) connector and confirm that the brake system warning light illuminates.

OK:

The brake system warning light does not turn off.


HINT:

If the brake system warning light turns off, there is a short in the brake fluid level warning switch (brake master cylinder reservoir assembly) circuit.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the H7 combination meter assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-16(SW) or A24-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the H7 combination meter assembly connector.


b.

Reconnect the A24 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Warning
50004 409 107

d.

Check the combination meter assembly.

OK:

The brake system warning light turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG