Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2020.07
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421654 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 67837C 1.INSTALL REAR DOOR DUST PROOF SEAL (for TMMF Made)

a.
B584314

Engage the claws to install 3 new rear door dust proof seals.


Hide 67837C 2.INSTALL REAR DOOR DUST PROOF SEAL (for TMC Made)

a.
B621544

Engage the claws to install 2 new rear door dust proof seals.

NOTICE:

Even if there were 3 dust proof seals at the time of removal, install 2 dust proof seals as shown in the illustration.



Hide 67872 3.INSTALL REAR DOOR WEATHERSTRIP

a.
B584313C01
2.927,0.208 3.094,0.135 true 3.125,0.042 3.417,0.25 0.292,0.208 10 false *a
*a Clip A


Engage the clip A and other clips to install the rear door weatherstrip.


Hide 68640A 4.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt A.


c.

Apply adhesive to the threads of the bolt A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B584312C01
2.49,1.615 2.688,1.792 0.198,0.177 10 true *a 1.656,1.323 1.823,1.49 0.167,0.167 10 true *b 1.635,0.646 1.802,0.813 0.167,0.167 10 true *b
*a Bolt A
*b Bolt B


Install the rear door check assembly with the bolt A and 2 bolts B.

Torque:
Bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 68230C 7.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 75708 8.INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

Hide 69204A 9.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the rear door outside handle frame sub-assembly.


b.
B584319C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the rear door outside handle frame sub-assembly as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 10.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B584309

Engage the guides to install the rear door outside handle rear pad.


Hide 69241G 11.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B584308

Engage the guide and claws to install the rear door outside handle front pad.


Hide 69227L 12.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B584307

Engage the claws to install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69240 13.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B584320C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door outside handle assembly as shown in the illustration.


b.
B584321

Move the lever and engage the claws as shown in the illustration.


Hide 69060A 14.INSTALL REAR DOOR LOCK ASSEMBLY

Hide 69840A 15.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Rear Power Window)

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.
B584304

Install the rear door window regulator assembly with the 6 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the connector.


d.

Engage the clamp.


Hide 69840A 16.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Rear Power Window)

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.
B594334

Install the rear door window regulator assembly with the 6 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Engage the clamp.


Hide 68104 17.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

w/ Rear Power Window:

i.

Connect the rear power window regulator switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the rear door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the rear power window regulator switch assembly.



b.
B584322C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.

NOTICE:

Be careful not to damage the rear door glass sub-assembly.



c.

Install the rear door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67408E 18.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.

Install the rear door window division bar sub-assembly with the 2 bolts and nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68152C 19.INSTALL REAR DOOR GLASS RUN

a.
B584300

Install the rear door glass run.


Hide 67842E 20.INSTALL REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

a.

Apply new butyl tape to the rear door panel.


b.
B584323C01
0.396,0.25 0.594,0.385 true 3.073,0.219 2.875,0.344 true 0.438,3.052 0.74,2.906 true 0.198,0.125 0.406,0.323 0.208,0.198 10 true *a 3.083,0.104 3.292,0.313 0.208,0.208 10 true *a 0.208,2.938 0.406,3.146 0.198,0.208 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and wire harness through a new rear door service hole cover.


c.

Install the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 67842E 21.INSTALL REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

a.

Apply new butyl tape to the rear door panel.


b.
B584324C01
0.344,0.271 0.604,0.385 true 2.906,0.344 3.083,0.229 true 0.677,2.833 0.5,2.969 true 0.146,0.146 0.365,0.354 0.219,0.208 10 true *a 3.073,0.115 3.281,0.313 0.208,0.198 10 true *a 0.25,2.854 0.469,3.073 0.219,0.219 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and wire harness through a new rear door service hole cover.


c.

Install the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 86160B 22.INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 68199 23.INSTALL REAR DOOR BELT REAR SEAL

a.
B565031

Install the rear door belt rear seal to the rear door glass inner weatherstrip.


Hide 68197A 24.INSTALL REAR DOOR BELT FRONT SEAL

a.
B584296

Install the rear door belt front seal to the rear door glass inner weatherstrip.


Hide 68174A 25.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B576064

Install the rear door glass weatherstrip inner with the rear door rear belt seal and rear door front belt seal.


Hide 69284D 26.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B584294

Engage the claw to install the rear door inside handle bezel plug.


Hide 69206C 27.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B584293

Engage the guides to install the rear door inside handle sub-assembly.


Hide 67604 28.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B584325C01
2.479,0.729 2.198,1 true 2.469,1.573 2.208,1.292 true 2.5,0.635 2.708,0.802 0.208,0.167 10 true *1 2.5,1.479 2.719,1.656 0.219,0.177 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Engage the guides to connect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.


b.
B584326C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws and clips to install the rear door trim board sub-assembly as shown in the illustration.


c.

Install the 3 screws.


d.
B584288

Engage the claw to close the rear door inside handle bezel plug.


Hide 29.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL (w/ Rear Power Window)

a.

Connect the connector.


b.
B584286

Engage the claws and guides to install the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 74272A 30.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Rear Power Window)

a.

Engage the claws and guides to install the rear door armrest base upper panel.


Hide 67674A 31.INSTALL REAR DOOR FRAME GARNISH

a.
B584285

Engage the claws and clip to install the rear door frame garnish.


Hide 69260E 32.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Rear Power Window)

a.

Install the rear door window regulator handle assembly and fully open the rear door glass sub-assembly.


b.

Remove the rear door window regulator handle assembly.


c.
B346721C02
2.333,0.542 2.646,0.74 0.313,0.198 10 false *a 2.906,0.542 3.094,0.74 0.188,0.198 10 false *b
*a Door Panel Side
*b Inside of Vehicle


Install the window regulator handle plate as shown in the illustration.


d.
B346725C03
2.885,0.833 3.198,0.99 0.313,0.156 10 false *a 0.615,0.5 0.927,0.656 0.313,0.156 10 false *b 0.51,1.021 0.823,1.177 0.313,0.156 10 false 0 1.031,0.094 1.344,0.25 0.313,0.156 10 false 60°
*a Front of Vehicle
*b Assemble with Glass in Fully Open Position


Install the rear door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.


Hide 33.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 34. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 35.INITIALIZE POWER WINDOW CONTROL SYSTEM