Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0420300 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

WIRING DIAGRAM

for LHD


B485324E30
2.438,1.01 2.896,1.208 0.458,0.198 10 false AUTO 4.354,1.01 4.813,1.208 0.458,0.198 10 false AUTO 4.115,1.49 6.708,2.01 2.594,0.521 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 4.146,0.906 4.604,1.104 0.458,0.198 10 false 4 2.906,0.906 3.365,1.104 0.458,0.198 10 false 8 1.365,1.5 2.948,1.885 1.583,0.385 10 false Power Window Regulator Switch Assembly 1.375,1.344 1.833,1.542 0.458,0.198 10 false K13 4.115,1.333 4.573,1.531 0.458,0.198 10 false K7


for RHD


B485324E26
2.438,1.01 2.896,1.208 0.458,0.198 10 false AUTO 4.354,1.01 4.813,1.208 0.458,0.198 10 false AUTO 4.115,1.49 6.708,2.01 2.594,0.521 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 4.146,0.906 4.604,1.104 0.458,0.198 10 false 4 2.906,0.906 3.365,1.104 0.458,0.198 10 false 8 1.365,1.5 2.948,1.885 1.583,0.385 10 false Power Window Regulator Switch Assembly 1.375,1.344 1.833,1.542 0.458,0.198 10 false L6 4.115,1.333 4.573,1.531 0.458,0.198 10 false L7


CAUTION / NOTICE / HINT

NOTICE:
·

If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Check that power window system customize settings "P Window Auto Up" and "P Window Auto Down" are set to "ON" before performing the following procedure.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS

·

After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.



HINT:

If the pulse sensor built into the power window regulator motor assembly (for front passenger door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>FAIL-SAFE CHART


PROCEDURE

1.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated
-
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.PERFORM INITIALIZATION (for Front Passenger Door)

NG

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
2.PERFORM INITIALIZATION (for Front Passenger Door)
a.

Initialize the power window regulator motor assembly (for front passenger door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
a.

Check that the front passenger door power window moves when the auto up and down functions of the power window regulator switch assembly are operated.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Front passenger door auto up and down functions are normal.



Result:
Proceed to
OK
NG



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))
a.

Disconnect the K7*1 or L7*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K13-8 (AUTO) - K7-4 (AUTO) Always Below 1 Ω
K13-8 (AUTO) or K7-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L6-8 (AUTO) - L7-4 (AUTO) Always Below 1 Ω
L6-8 (AUTO) or L7-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR