Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM J

G16E-GTS ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A468622E03
6.125,4.771 6.688,5.063 0.563,0.292 10 false D104 6.135,4.948 7.115,5.448 0.979,0.5 10 false ECM 5.875,0.635 6.49,0.833 0.615,0.198 10 false IGT1 5.625,0.646 5.938,0.844 0.313,0.198 10 false 72 5.635,2.271 5.948,2.469 0.313,0.198 10 false 71 5.875,2.26 6.49,2.458 0.615,0.198 10 false IGT2 5.646,4.031 5.958,4.229 0.313,0.198 10 false 70 5.875,4.01 6.49,4.208 0.615,0.198 10 false IGT3 4.969,0.646 5.125,0.844 0.156,0.198 10 false 2 4.979,2.24 5.135,2.438 0.156,0.198 10 false 2 4.958,4.021 5.115,4.219 0.156,0.198 10 false 2 4.563,0.75 5.177,0.948 0.615,0.198 10 false IGT1 4.573,2.365 5.188,2.563 0.615,0.198 10 false IGT2 4.573,4.146 5.188,4.344 0.615,0.198 10 false IGT3 3.948,0.75 4.26,0.948 0.313,0.198 10 false +B 3.781,0.625 3.938,0.823 0.156,0.198 10 false 1 3.781,2.25 3.938,2.448 0.156,0.198 10 false 1 3.74,4.01 3.896,4.208 0.156,0.198 10 false 1 3.948,2.365 4.26,2.563 0.313,0.198 10 false +B 3.927,4.135 4.24,4.333 0.313,0.198 10 false +B 3.781,0.979 3.938,1.177 0.156,0.198 10 false 3 3.76,2.573 3.938,2.833 0.177,0.26 10 false 3 3.76,4.438 3.917,4.635 0.156,0.198 10 false 3 3.927,1.073 4.385,1.271 0.458,0.198 10 false GND 3.927,2.688 4.385,2.885 0.458,0.198 10 false GND 3.927,4.531 4.385,4.729 0.458,0.198 10 false GND 3.646,1.469 3.958,1.667 0.313,0.198 10 false D1 3.625,1.656 5.583,1.854 1.958,0.198 10 false No. 1 Ignition Coil Assembly 3.656,3.115 3.969,3.313 0.313,0.198 10 false D2 3.656,3.281 5.656,3.479 2,0.198 10 false No. 2 Ignition Coil Assembly 3.677,4.896 3.99,5.094 0.313,0.198 10 false D3 3.667,5.094 5.667,5.281 2,0.188 10 false No. 3 Ignition Coil Assembly 2.76,0.927 3.219,1.125 0.458,0.198 10 false INJ 1.979,0.615 2.135,0.813 0.156,0.198 10 false 5 1.99,1.104 2.146,1.302 0.156,0.198 10 false 1 1.156,1.104 1.313,1.302 0.156,0.198 10 false 2 1.156,0.625 1.365,0.813 0.208,0.188 10 false 3 1.531,1.531 2.25,1.74 0.719,0.208 10 false IGP 0.417,4.115 1.073,4.365 0.656,0.25 10 false IGP-MAIN 1.74,2.865 2.354,3.063 0.615,0.198 10 false IGPD 2.125,2.76 2.438,2.958 0.313,0.198 10 false 24 0.469,5.031 0.99,5.49 0.521,0.458 10 false ENG 0.781,3.26 1.24,3.458 0.458,0.198 10 false H45 0.771,3.427 2.604,3.927 1.833,0.5 10 false Certification ECU (Smart Key ECU Assembly)*1 0.594,5.833 1.76,6.146 1.167,0.313 10 false Battery 1.167,4.875 2.708,5.365 1.542,0.49 10 false Ignition or Starter Switch Assembly*2 1.188,4.708 1.646,4.906 0.458,0.198 10 false H54 1.885,4.292 2.604,4.5 0.719,0.208 10 false IG1 2.198,4.188 2.51,4.385 0.313,0.198 10 false 8 2.323,6.25 5.302,6.708 2.979,0.458 10 false *1: w/ Entry and Start System 4.552,6.25 7.156,6.646 2.604,0.396 10 false *2: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Perform a spark test first. If none of the cylinders spark, or if only some cylinders do not spark, check this circuit to determine if the ignition coil and spark plug are normal.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.

Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D1-1 (+B) - D1-3 (GND) Ignition switch ON 11 to 14 V
D2-1 (+B) - D2-3 (GND) Ignition switch ON 11 to 14 V
D3-1 (+B) - D3-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (IGT1) - D104-72 (IGT1) Always Below 1 Ω
D2-2 (IGT2) - D104-71 (IGT2) Always Below 1 Ω
D3-2 (IGT3) - D104-70 (IGT3) Always Below 1 Ω
D1-2 (IGT1) or D104-72 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
D2-2 (IGT2) or D104-71 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
D3-2 (IGT3) or D107-70 (IGT3) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-3 (GND) - Body ground Always Below 1 Ω
D2-3 (GND) - Body ground Always Below 1 Ω
D3-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGP RELAY - IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGP RELAY - IGNITION COIL ASSEMBLY)
a.

Remove the IGP relay from No. 1 engine room relay block assembly.


b.

Disconnect the ignition coil assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - D1-1 (+B) Always Below 1 Ω
5 (IGP relay) - D2-1 (+B) Always Below 1 Ω
5 (IGP relay) - D3-1 (+B) Always Below 1 Ω
5 (IGP relay) or D1-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP relay) or D2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP relay) or D3-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR