Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P003312  Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery  


DESCRIPTION

The air by-pass valve assembly is installed in the air outlet duct. It opens and closes in response to drive commands from the ECM. During normal boosting, the air by-pass valve assembly is closed, and when the throttle valve is closed while the boost pressure is applied, the air by-pass valve assembly opens and the excess pressure between the turbocharger and throttle valve is released to prevent the surge phenomenon*.

*: This phenomenon is when the intake air flow reverses. As a result, an abnormal noise is easily generated during deceleration.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P003312 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery Short circuit in air by-pass valve assembly circuit and power supply circuit (1 trip detection logic).
·

Short in air by-pass valve assembly circuit

·

Air by-pass valve assembly

·

ECM


- SAE: P0035

MONITOR DESCRIPTION

The ECM monitors the output voltage while the air by-pass valve assembly is operating.

The air by-pass valve assembly turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the air by-pass valve assembly circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

A330723E39
4.448,0.958 4.802,0.667 4.802,0.667 5.021,0.667 false 3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.76,0.677 1.375,0.875 0.615,0.198 10 false 50 km/h 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.396,2.365 1.313,2.75 0.917,0.385 10 false Ignition Switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [D] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 5.083,0.604 6.031,0.792 0.948,0.188 10 false Released 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.125,1.417 3.604,1.615 0.479,0.198 10 false [B] 4.906,1.406 5.365,1.604 0.458,0.198 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Quickly release the accelerator pedal from the fully depressed position [C].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P003312.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [B] through [D] again.




WIRING DIAGRAM

A468609E03
0.646,3 1.719,3.198 1.073,0.198 10 false Battery 4.094,1.646 5.229,2.427 1.135,0.781 10 false Air By-pass Valve Assembly 5.875,0.896 6.292,1.135 0.417,0.24 10 false ABV 5.875,2.677 6.406,2.896 0.531,0.219 10 false MREL 6.094,4.042 6.958,4.563 0.865,0.521 10 false ECM 5.531,0.833 5.948,1.073 0.417,0.24 10 false 20 5.469,1.042 5.885,1.281 0.417,0.24 10 false D104 5.521,2.594 5.938,2.833 0.417,0.24 10 false 15 5.469,2.792 5.885,3.031 0.417,0.24 10 false A106 5.135,0.948 5.302,1.115 0.167,0.167 10 false 2 4.104,0.948 4.271,1.115 0.167,0.167 10 false 1 4.094,1.479 4.51,1.719 0.417,0.24 10 false D101 3.438,1.198 4.271,1.365 0.833,0.167 10 false EFI NO.3 0.646,1.229 1.698,1.5 1.052,0.271 10 false EFI-MAIN NO.1 2.115,2.125 3.219,2.417 1.104,0.292 10 false EFI-MAIN NO.1 2.052,1.677 2.208,1.875 0.156,0.198 10 false 1 2.875,1.677 3.031,1.875 0.156,0.198 10 false 2 2.875,0.938 3.031,1.135 0.156,0.198 10 false 5 0.563,2.063 1.594,2.26 1.031,0.198 10 false ENG 2.052,0.938 2.208,1.135 0.156,0.198 10 false 3 4.281,0.938 4.521,1.146 0.24,0.208 10 false +B 4.781,0.927 5.177,1.188 0.396,0.26 10 false ABV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)
a.

Enter the following menus.

Powertrain > Engine > Active Test
Active Test Display
Activate the Air Bypass Valve
Data List Display
Air Bypass Valve Control
50004 372 12 282

b.

According to the display on the GTS, perform the Active Test and check the operation and operation sound of the air by-pass valve.

OK:
Active Test Standard
ON
·

ON is displayed for Data List item "Air Bypass Valve Control"

·

Air by-pass valve operates (operation sound is normal)





Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TURBOCHARGER SUB-ASSEMBLY
2.INSPECT TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY (AIR BY-PASS VALVE MALFUNCTION)

3.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)
a.

Disconnect the air by-pass valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-2 (ABV) or C62-67 (ABV) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312)
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Start the engine and warm it up.


d.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


e.

Enter the following menus.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

f.

Input the DTC: P003312.


g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P003312 is output)
B




A

B