Home › Engine / Hybrid System › G16E-GTS (INTAKE / EXHAUST) › TURBOCHARGER › from 2020.09
RM36W0E _51 Engine / Hybrid System _095906 G16E-GTS INTAKE / EXHAUST _0449874 TURBOCHARGER A

G16E-GTS INTAKE / EXHAUST  TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 2.DRAIN ENGINE COOLANT

Hide 25051 3.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55735A 5.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 55734A 6.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55815E 7.REMOVE NO. 1 FRONT VENTILATOR SEAL (for RHD)

Hide 55815E 8.REMOVE NO. 1 FRONT VENTILATOR SEAL (for LHD)

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55225 11.REMOVE DASH PANEL HEAT INSULATOR

a.
A480421

Disengage the clamp.


b.

Remove the 3 nuts and dash panel heat insulator.


Hide 17751 12.REMOVE NO. 1 AIR CLEANER INLET

a.
A480384

Remove the 2 clips and No. 1 air cleaner inlet.


Hide 17881 13.SEPARATE NO. 1 AIR CLEANER HOSE

a.
A480385

Loosen the hose clamp to separate the No. 1 air cleaner hose from the air cleaner cap sub-assembly.


Hide 14.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A480386

Disconnect the 3 connectors and disenngage the 6 clamps.


b.
A476716

Remove the air cleaner case sub-assembly.


Hide 17893 15.REMOVE INTAKE AIR RESONATOR

a.
A480422

Remove the 2 bolts.


b.

Loosen the 2 hose clamps to remove the intake air resonator.


Hide 17311A 16.DISCONNECT NO. 1 AIR INLET DUCT

a.
A480423

Remove the bolt.


b.

Slide the hose clip to disconnect the ventilation hose.


c.

Loosen the 2 hose clamps to remove the No. 1 air inlet duct.


Hide 17271 17.REMOVE NO. 1 TURBO INSULATOR

a.
A480424

Remove the 3 bolts and No. 1 turbo insulator.


Hide 15474 18.SEPARATE TURBO OIL OUTLET PIPE

a.
A480425

Remove the 2 bolts to separate the turbo oil outlet pipe from the turbocharger sub-assembly.


Hide 17342D 19.DISCONNECT NO. 2 AIR HOSE

a.
A480426

Loosen the hose clamp to disconnect the No. 2 air hose.


Hide 25771B 20.DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE

a.
A480427

Disconnect the No. 2 vacuum transmitting hose.


Hide 15407A 21.REMOVE TURBO OIL INLET PIPE UNION BOLT

a.
A480428

Remove the turbo oil inlet pipe union bolt.


Hide 16027 22.DISCONNECT NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A480429

Slide the hose clip to disconnect the No. 1 turbo water hose.


b.

Remove the bolt and union bolt to disconnect the No. 1 turbo water pipe sub-assembly.


Hide 23.DISCONNECT WIRE HARNESS

a.
A480430

Disconnect the connector.


Hide 17201 24.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A481181

Remove the 7 nuts.


b.

Remove the collar.


c.
A481182

Using an E8 "TORX" socket wrench, remove the 7 stud bolts.


d.

Remove the turbocharger sub-assembly.


Hide 17173 25.REMOVE EXHAUST MANIFOLD TO HEAD GASKET

a.
A480445

Remove the exhaust manifold to head gasket.


Hide 17274 26.DISCONNECT COMPRESSOR INLET ELBOW

a.
A481183

Remove the bolt, nut and compressor inlet elbow.


b.
A481184

Remove the gasket.


Hide 15407 27.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A480433

Remove the union bolt and turbo oil inlet pipe sub-assembly.


Hide 16027 28.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A480434

Remove the 2 bolts and No. 1 turbo water pipe sub-assembly.


Hide 16347A 29.REMOVE TURBO WATER PIPE GASKET

a.
A481185

Remove the turbo water pipe gasket from the No. 1 turbo water pipe sub-assembly.


Hide 30.REMOVE STUD BOLT

a.
A481186

Using an E8 "TORX" socket wrench, remove the stud bolt from the turbocharger sub-assembly.