Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P023511  Turbocharger/Supercharger Boost Sensor "A" Circuit Short to Ground  


DESCRIPTION

The internal sensor in the No. 2 turbo pressure sensor detects the air outlet duct internal pressure as a voltage.

A327839E08
0.073,0.052 0.844,0.25 0.771,0.198 10 false Voltage (V) 0.958,0.26 3.167,0.573 2.208,0.313 10 false Air outlet duct internal pressure 0.24,0.74 1.01,0.938 0.771,0.198 10 false 4.5 0.25,1.563 1.021,1.76 0.771,0.198 10 false 2.0 0.25,2.01 1.021,2.208 0.771,0.198 10 false 1.0 3.021,2.375 3.396,2.802 0.375,0.427 10 false kPa 3,2.854 3.427,3.24 0.427,0.385 10 false psi 0.854,2.563 1.302,2.771 0.448,0.208 10 false 13.30 1.458,2.563 1.906,2.771 0.448,0.208 10 false 96.15 2.51,2.563 3.083,2.781 0.573,0.219 10 false 303.30 0.917,3.042 1.271,3.271 0.354,0.229 10 false 1.93 1.49,3.052 2.031,3.323 0.542,0.271 10 false 13.94 2.552,3.052 3.031,3.281 0.479,0.229 10 false 43.98

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P023511 Turbocharger/Supercharger Boost Sensor "A" Circuit Short to Ground The output voltage from the No. 2 turbo pressure sensor is below 0.97 V for 3 seconds or more (1 trip detection logic).
·

Open or short in No. 2 turbo pressure sensor circuit

·

No. 2 turbo pressure sensor

·

ECM


Comes on SAE: P0237

HINT:

When a DTC is output, check the Data List item "Boost Pressure Sensor" using the GTS.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Boost Pressure Sensor Malfunction
P023511 Approximately 0 kPa [0 psi]
·

Short in PTA circuit to ground

·

Short in PTA circuit to EPR circuit

·

Open in VCPR circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM calculates the air outlet duct internal pressure from the No.2 turbo pressure sensor output voltage. If the No. 2 turbo pressure sensor output voltage is not within the normal range, there may be a malfunction in the No. 2 turbo pressure sensor or an open or short circuit. In this case, the ECM illuminates the MIL and stores a DTC.

Example:

When the sensor output voltage is below 0.97 V for 3 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components No. 2 turbo pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON.

6.

Turn the GTS on.

7.

Start the engine and wait 5 seconds or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P023511.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A477652E01
5.302,3.302 5.813,3.563 0.51,0.26 10 false ECM 0.531,3.063 3.49,3.323 2.958,0.26 10 false No. 2 Turbo Pressure Sensor 0.552,2.896 0.917,3.094 0.365,0.198 10 false D94 5.302,3.115 5.667,3.313 0.365,0.198 10 false D104 1.406,1.031 1.771,1.229 0.365,0.198 10 false VC 1.323,1.729 1.75,1.979 0.427,0.25 10 false PTA 1.438,2.51 1.802,2.708 0.365,0.198 10 false E2 1.74,0.917 2.104,1.115 0.365,0.198 10 false 3 1.75,1.594 2.115,1.792 0.365,0.198 10 false 1 1.75,2.365 2.115,2.563 0.365,0.198 10 false 2 4.354,0.906 4.615,1.083 0.26,0.177 10 false 80 4.281,1.594 4.542,1.771 0.26,0.177 10 false 103 4.323,2.354 4.677,2.656 0.354,0.302 10 false 79 4.615,0.906 5.188,1.167 0.573,0.26 10 false VPTA 4.625,1.604 4.99,1.802 0.365,0.198 10 false PTA 4.635,2.365 5.292,2.646 0.656,0.281 10 false EPTA 5.615,0.688 5.979,0.885 0.365,0.198 10 false 5V

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D94-3(VC) - D94-2(E2) Ignition switch ON 4.5 to 5.5 V
D94-1(PTA) - D94-2(E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D94-3(VC) - D94-1(PTA) Ignition switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 2 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 2 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D94-3(VC) - D104-80(VPTA) Always Below 1 Ω
D94-3(VC) or D104-80(VPTA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR