Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P05042B  Brake Switch "A"/"B" Signal Cross Coupled  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, Data List items Stop Light SW is ON when the brake pedal is depressed.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P05042B Brake Switch "A"/"B" Signal Cross Coupled Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch to ON
(b) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- SAE: P0504

WIRING DIAGRAM

A468615E05
6.25,0.333 6.708,0.531 0.458,0.198 10 false STP 6.271,1.135 6.729,1.333 0.458,0.198 10 false ST1- 6.365,2.75 7.156,3.219 0.792,0.469 10 false ECM 4.656,2.625 5.771,3.177 1.115,0.552 10 false Stop Light Switch Assembly 0.604,3.844 1.24,4.073 0.635,0.229 10 false Battery 4.344,3.552 6.865,4.24 2.521,0.688 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition or Starter Switch Assembly*2 4.51,0.344 4.667,0.542 0.156,0.198 10 false 7 4.542,1.146 4.698,1.344 0.156,0.198 10 false 6 4.531,1.76 4.688,1.958 0.156,0.198 10 false 2 5.74,0.333 5.906,0.583 0.167,0.25 10 false 3 5.75,1.135 5.917,1.385 0.167,0.25 10 false 5 6.01,0.333 6.281,0.625 0.271,0.292 10 false 21 6.01,1.125 6.26,1.375 0.25,0.25 10 false 22 6.375,2.563 6.792,2.781 0.417,0.219 10 false A106 4.677,2.448 5.052,2.635 0.375,0.188 10 false A63 4.708,0.469 4.865,0.667 0.156,0.198 10 false B 4.729,1.26 4.885,1.458 0.156,0.198 10 false B 5.563,0.469 5.719,0.667 0.156,0.198 10 false L 5.563,1.24 5.719,1.438 0.156,0.198 10 false L 4.698,1.875 5.104,2.073 0.406,0.198 10 false GND 3.313,0.573 4.229,0.74 0.917,0.167 10 false STOP 3.042,1.385 4.125,1.719 1.083,0.333 10 false ECU-IGP NO. 3 2.385,2.188 3.146,2.448 0.76,0.26 10 false IGP 0.458,2.406 0.969,2.792 0.51,0.385 10 false ENG 0.375,0.615 1.531,0.896 1.156,0.281 10 false INP STD NO. 1-3 0.885,1.417 1.938,1.708 1.052,0.292 10 false IGP-MAIN 2.042,1.74 2.292,1.948 0.25,0.208 10 false 2 2.854,1.74 3.104,1.948 0.25,0.208 10 false 1 2.865,1.104 3.115,1.313 0.25,0.208 10 false 5 2.042,1.104 2.292,1.313 0.25,0.208 10 false 3 1.427,3.656 4.354,3.938 2.927,0.281 10 false *1: w/ Entry and Start System 1.417,4.229 4.344,4.51 2.927,0.281 10 false *2: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light SW
Depressed ON
Released OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7(B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-6(B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 D RELAY)

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2(GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
F102339C01
0.729,0.229 1.042,0.427 0.313,0.198 10 *a 2.583,0.219 2.896,0.417 0.313,0.198 10 *b
*a Brake Pedal Depressed
*b Brake Pedal Released


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A106-22(ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A106-21(STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-5(L) - A106-22(ST1-) Always Below 1 Ω
A63-3(L) - A106-21(STP) Always Below 1 Ω
A63-5(L) or A106-22(ST1-) - Body ground and other terminals Always 10 kΩ or higher
A63-3(L) or A106-21(STP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)