Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P020113  Cylinder 1 Injector "A" Circuit Open  P020213  Cylinder 2 Injector "A" Circuit Open  P020313  Cylinder 3 Injector "A" Circuit Open  P062D13  Fuel Injector Driver Circuit Performance Bank 1 Circuit Open  


DESCRIPTION

The D-4S system has two fuel injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines which fuel injection system to use in accordance with the engine conditions. The direct injection system uses an injector driver (EDU) built into the ECM to rapidly operate the direct fuel injector assemblies. It converts injection request signals from the ECM to high-voltage and high-current injector-drive signals that drive the direct fuel injector assemblies.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P020113 Cylinder 1 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in direct fuel injector assembly (No. 1 cylinder) circuit for 40 times or more.

·

Open or short to ground in direct fuel injector assembly (No. 1 cylinder) circuit for 20 times or more.

·

Direct fuel injector assembly (No. 1 cylinder) circuit current reaches the high limit for 20 times or more.


·

Open or short in direct fuel injector assembly (No. 1 cylinder) circuit

·

Direct fuel injector assembly (No. 1 cylinder)

·

EDU relay

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on SAE: P0201
P020213 Cylinder 2 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in direct fuel injector assembly (No. 2 cylinder) circuit for 40 times or more.

·

Open or short to ground in direct fuel injector assembly (No. 2 cylinder) circuit for 20 times or more.

·

Direct fuel injector assembly (No. 2 cylinder) circuit current reaches the high limit for 20 times or more.


·

Open or short in direct fuel injector assembly (No. 2 cylinder) circuit

·

Direct fuel injector assembly (No. 2 cylinder)

·

EDU relay

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on SAE: P0202
P020313 Cylinder 3 Injector "A" Circuit Open Either of following conditions is met (1 trip detection logic):
·

Short to +B in direct fuel injector assembly (No. 3 cylinder) circuit for 40 times or more.

·

Open or short to ground in direct fuel injector assembly (No. 3 cylinder) circuit for 20 times or more.

·

Direct fuel injector assembly (No. 3 cylinder) circuit current reaches the high limit for 20 times or more.


·

Open or short in direct fuel injector assembly (No. 3 cylinder) circuit

·

Direct fuel injector assembly (No. 3 cylinder)

·

EDU relay

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on SAE: P0203
P062D13 Fuel Injector Driver Circuit Performance Bank 1 Circuit Open Open or short in direct fuel injector assembly (all cylinders) circuits for 60 times or more (1 trip detection logic).
·

Open or short in direct fuel injector assembly circuit

·

Direct fuel injector assembly

·

EDU relay

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on SAE: P062D

MONITOR DESCRIPTION

The fuel injection sequence occurs in numerical order from No. 1 to No. 3.

The ECM monitors the Injector Driver (EDU) at all times. If drivers or direct fuel injector assembly is malfunctioning, the EDU sends direct fuel injector assembly operation condition signals (fail signals) to the ECM. When the ECM receives the signals, the ECM stops the fuel injection control of the appropriate cylinders, cuts voltage to the appropriate EDU relay, and illuminates the MIL.

MONITOR STRATEGY

Required Sensors/Components (Main) Direct fuel injector assembly
ECM (injector driver)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Idle the engine for 15 seconds or more [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P020113, P020213, P020313 or P062D13

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A468613E03
0.448,5.792 1.365,5.99 0.917,0.198 10 false ENG 2.333,1.198 5.479,1.531 3.146,0.333 10 false No. 1 Fuel Injector Assembly (for Direct Injection) 2.333,2.198 5.531,2.552 3.198,0.354 10 false No. 2 Fuel Injector Assembly (for Direct Injection) 2.333,3.208 4.177,3.76 1.844,0.552 10 false No. 3 Fuel Injector Assembly (for Direct Injection) 2.333,1.031 2.792,1.229 0.458,0.198 10 false F10 2.333,2.031 2.792,2.229 0.458,0.198 10 false F11 2.333,3.021 2.792,3.219 0.458,0.198 10 false F12 3.24,0.667 3.396,0.865 0.156,0.198 10 false 1 3.24,1.667 3.396,1.865 0.156,0.198 10 false 1 3.24,2.667 3.396,2.865 0.156,0.198 10 false 1 2.031,5.271 2.188,5.469 0.156,0.198 10 false 1 4.552,4.719 4.708,4.917 0.156,0.198 10 false 1 2.344,0.667 2.5,0.865 0.156,0.198 10 false 2 2.344,1.667 2.5,1.865 0.156,0.198 10 false 2 2.344,2.667 2.5,2.865 0.156,0.198 10 false 2 2.833,5.271 2.99,5.469 0.156,0.198 10 false 2 3.76,4.719 3.917,4.917 0.156,0.198 10 false 2 2.542,0.698 2.854,0.896 0.313,0.198 10 false #1 2.542,1.688 2.854,1.885 0.313,0.198 10 false #2 2.542,2.677 2.854,2.875 0.313,0.198 10 false #3 2.948,2.677 3.406,2.875 0.458,0.198 10 false #30 0.667,6.5 1.281,6.698 0.615,0.198 10 false Battery 6.354,6.531 7.094,7.094 0.74,0.563 10 false ECM 2.938,1.688 3.396,1.885 0.458,0.198 10 false #20 2.938,0.698 3.396,0.896 0.458,0.198 10 false #10 6.219,0.406 6.833,0.604 0.615,0.198 10 false #1D+ 6.219,0.813 6.833,1.01 0.615,0.198 10 false #1D- 6.219,1.396 6.833,1.594 0.615,0.198 10 false #2D+ 6.219,1.792 6.833,1.99 0.615,0.198 10 false #2D- 6.219,2.396 6.833,2.594 0.615,0.198 10 false #3D+ 6.219,2.792 6.833,2.99 0.615,0.198 10 false #3D- 6.219,3.26 6.833,3.458 0.615,0.198 10 false +BD1 6.219,4.844 6.833,5.042 0.615,0.198 10 false IREL 6.219,5.385 6.833,5.583 0.615,0.198 10 false MREL 6.219,5.958 6.833,6.156 0.615,0.198 10 false E1D1 5.833,0.396 6.448,0.594 0.615,0.198 10 false D104 5.833,0.792 6.448,0.99 0.615,0.198 10 false D104 5.833,1.385 6.448,1.583 0.615,0.198 10 false D104 5.844,1.792 6.458,1.99 0.615,0.198 10 false D104 5.833,2.385 6.448,2.583 0.615,0.198 10 false D104 5.833,2.792 6.448,2.99 0.615,0.198 10 false D104 5.917,0.219 6.229,0.417 0.313,0.198 10 false 31 5.917,0.635 6.229,0.833 0.313,0.198 10 false 12 5.917,1.229 6.229,1.427 0.313,0.198 10 false 33 5.917,1.635 6.229,1.833 0.313,0.198 10 false 14 5.917,2.219 6.229,2.417 0.313,0.198 10 false 35 5.917,2.625 6.229,2.823 0.313,0.198 10 false 16 5.833,4.844 6.448,5.042 0.615,0.198 10 false A106 5.833,5.385 6.448,5.583 0.615,0.198 10 false A106 5.833,5.958 6.448,6.156 0.615,0.198 10 false A106 5.917,5.802 6.229,6 0.313,0.198 10 false 54 5.917,5.219 6.229,5.417 0.313,0.198 10 false 15 5.917,4.677 6.229,4.875 0.313,0.198 10 false 34 6.219,3.771 6.833,3.969 0.615,0.198 10 false +BD2 6.219,4.26 6.833,4.458 0.615,0.198 10 false +BD3 5.833,3.26 6.448,3.458 0.615,0.198 10 false D104 5.833,3.76 6.448,3.958 0.615,0.198 10 false D104 5.833,4.26 6.448,4.458 0.615,0.198 10 false D104 5.917,3.094 6.229,3.292 0.313,0.198 10 false 19 5.917,3.594 6.229,3.792 0.313,0.198 10 false 38 5.917,4.094 6.229,4.292 0.313,0.198 10 false 18 5,3.417 6.531,3.615 1.531,0.198 10 false EDU-S NO.1 5,3.917 6.531,4.115 1.531,0.198 10 false EDU-S NO.2 5,4.417 6.531,4.615 1.531,0.198 10 false EDU-S NO.3 4.083,5.135 4.542,5.333 0.458,0.198 10 false EDU 2.083,5.719 4.073,5.917 1.99,0.198 10 false EFI-MAIN NO.1 0.51,5 2.5,5.198 1.99,0.198 10 false EFI-MAIN NO.1 0.833,4.417 1.292,4.615 0.458,0.198 10 false EDU 2.031,4.719 2.188,4.917 0.156,0.198 10 false 3 2.833,4.719 2.99,4.917 0.156,0.198 10 false 5 3.76,4.135 3.917,4.333 0.156,0.198 10 false 3 4.552,4.135 4.708,4.333 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

If the current from the EDU relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT (DTC P020113, P020213, P020313 AND/OR P062D13)
a.

Enter the following menus.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P020113, P020213, P020313 and/or P062D13 is output A
3 or more of the following DTCs are output: P020113, P020213, P020313 and/or P062D13 B
P062D13 is output




A

2.CHECK HARNESS AND CONNECTOR

B

4.INSPECT EDU RELAY
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D104-31(#1D+) - D104-12(#1D-) 20°C (68°F) 1.34 to 1.64 Ω
D104-33(#2D+) - D104-14(#2D-) 20°C (68°F) 1.34 to 1.64 Ω
D104-35(#3D+) - D104-16(#3D-) 20°C (68°F) 1.34 to 1.64 Ω
D104-31(#1D+) or D104-12(#1D-) - Body ground and other terminals Always 1 MΩ or higher
D104-33(#2D+) or D104-14(#2D-) - Body ground and other terminals Always 1 MΩ or higher
D104-35(#3D+) or D104-16(#3D-) - Body ground and other terminals Always 1 MΩ or higher


HINT:

The standard values shown are direct fuel injector assembly resistance values.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT DIRECT FUEL INJECTOR ASSEMBLY (RESISTANCE)
3.INSPECT DIRECT FUEL INJECTOR ASSEMBLY (RESISTANCE)
a.

Check the resistance of the direct fuel injector assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL INJECTOR (for Direct Injection)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the direct fuel injector assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (DIRECT FUEL INJECTOR ASSEMBLY - ECM)

NG

4.INSPECT EDU RELAY

Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EDU RELAY)

NG

REPLACE EDU RELAY

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EDU RELAY)
a.
A468638C02
0.052,0.052 0.365,0.208 0.313,0.156 10 false *1 1.823,2.135 2.135,2.292 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 EDU Relay


Remove the EDU relay from the No. 1 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3(EDU relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EDU RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EDU RELAY)

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EDU RELAY)
a.
A468638C02
0.052,0.052 0.365,0.208 0.313,0.156 10 false *1 1.823,2.135 2.135,2.292 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 EDU Relay


Remove the EDU relay from the No. 1 engine room relay block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2(EDU relay) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EDU RELAY)
7.CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)
a.

Remove the EDU relay from the No. 1 engine room relay block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5(EDU relay) - D104-19(+BD1) Always Below 1 Ω
5(EDU relay) - D104-38(+BD2) Always Below 1 Ω
5(EDU relay) - D104-18(+BD3) Always Below 1 Ω
1(EDU relay) - A106-34(IREL) Always Below 1 Ω
5(EDU relay), D104-19(+BD1), D104-38(+BD2) or D104-18(+BD3) - Body ground and other terminals Always 10 kΩ or higher
1(EDU relay) or A106-34(IREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EDU RELAY)
a.

Remove the EFI-MAIN NO. 1 relay, EFI-MAIN NO. 3 relay and EDU relay from the No. 1 engine room relay block assembly.

HINT:

Remove the EFI-MAIN NO. 3 relay and EDU relay connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5(EFI-MAIN NO. 1 relay) - 2(EDU relay) Always Below 1 Ω
5(EFI-MAIN NO. 1 relay) or 2(EDU relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT EFI-MAIN NO. 1 RELAY
a.

Inspect the EFI-MAIN NO. 1 relay.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPLACE EFI-MAIN NO. 1 RELAY

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
a.
A468644C03
0.083,0.104 0.396,0.26 0.313,0.156 10 false *1 1.677,2.042 1.99,2.198 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 EFI-MAIN NO. 1 Relay


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3(EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V
1(EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2(EFI-MAIN NO. 1 relay) - A106-15 (MREL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR