Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P166014  Air Intake Control Valve Circuit Short to Ground or Open  


DESCRIPTION

The air cleaner is equipped with two inlets, one of which is opened or closed by the Air Intake Control Valve (AICV). This system reduces intake noise and increases engine power at low-to-high engine speed range. When the engine is operating in the low-to-mid speed range, this control operates the AICV to close one of the air cleaner inlets. When the engine speed is more than 3600 rpm, the ECM activates VSV and opens the AICV.

A468640E01
2.667,1.198 2.167,0.417 true 3.417,1.188 3.833,0.667 true 6.083,1.083 5.708,0.333 true 1.125,1.271 0.667,0.75 true 0.25,3.25 0.74,1.781 true 0.25,3.25 0.854,2.854 true 1.198,1.667 2,3.417 true 2.281,2.438 2.917,2.833 true 0.844,0.115 2.406,0.594 1.563,0.479 10 false Vacuum Switching Valve Assembly (for AICV) 4.99,0.083 7.073,0.333 2.083,0.25 10 false AICV Open (VSV: ON) 5.354,3.083 6.583,3.281 1.229,0.198 10 false 3600 rpm 5.25,3.333 6.323,3.531 1.073,0.198 10 false Engine Speed 3.604,0.458 4.833,0.656 1.229,0.198 10 false Vacuum Pump 0.156,0.583 1.229,0.781 1.073,0.198 10 false Actuator 1.75,3.469 5.115,3.667 3.365,0.198 10 false Air Intake Control Valve (AICV) 0.094,3.302 1.167,3.5 1.073,0.198 10 false Air Intake 2.938,2.854 4.01,3.052 1.073,0.198 10 false Air Cleaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P166014 Air Intake Control Valve Circuit Short to Ground or Open Voltage of terminal air intake control valve of the ECM is low when the VSV is not operating for 3 seconds or more (1 trip detection logic).
·

Open or short in vacuum switching valve assembly (for AICV) circuit

·

Vacuum switching valve assembly (for AICV)

·

EFI-MAIN NO. 1 relay

·

ECM


- SAE: P1660

WIRING DIAGRAM

A468646E03
0.604,3.01 1.271,3.281 0.667,0.271 10 false Battery 0.344,1.969 1.979,2.396 1.635,0.427 10 false ENG 0.313,0.938 1.365,1.219 1.052,0.281 10 false EFI-MAIN NO. 1 1.75,1.104 2.906,1.385 1.156,0.281 10 false EFI-MAIN NO. 1 4.021,1.469 4.74,1.698 0.719,0.229 10 false EFI NO. 3 6.302,1.198 6.76,1.396 0.458,0.198 10 false AICV 6.302,0.292 6.76,0.49 0.458,0.198 10 false MREL 6.302,2.729 6.76,2.927 0.458,0.198 10 false E1 5.906,0.281 6.26,0.5 0.354,0.219 10 false A106 5.927,2.729 6.292,2.948 0.365,0.219 10 false A106 5.979,0.104 6.188,0.302 0.208,0.198 10 false 15 6,1.146 6.229,1.344 0.229,0.198 10 false 49 6.01,2.552 6.208,2.75 0.198,0.198 10 false 10 5.927,1.313 6.292,1.531 0.365,0.219 10 false D104 6.479,3.219 7.146,3.646 0.667,0.427 10 false ECM 4.698,1.646 5.073,1.875 0.375,0.229 10 false D98 4.677,1.802 6.219,2.375 1.542,0.573 10 false Vacuum Switching Valve Assembly (for AICV) 2.5,0.635 2.698,0.833 0.198,0.198 10 false 5 1.833,0.635 2.031,0.833 0.198,0.198 10 false 3 2.5,0.156 2.698,0.354 0.198,0.198 10 false 2 1.833,0.146 2.031,0.344 0.198,0.198 10 false 1 4.677,1.188 4.875,1.385 0.198,0.198 10 false 2 5.625,1.188 5.823,1.385 0.198,0.198 10 false 1 5.26,1.198 5.719,1.396 0.458,0.198 10 false AIRV 4.844,1.198 5.042,1.385 0.198,0.188 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR AICS)
A336911C01
1.417,1.083 1.5,0.75 1.5,0.75 1.583,0.75 true 2.927,1.271 3.01,1.604 3.01,1.604 3.094,1.604 true 0.646,1.365 0.854,1.906 0.854,1.906 0.938,1.906 true 2.104,1.365 2.313,1.906 2.313,1.906 2.396,1.906 true 1.948,1.594 1.865,1.927 1.865,1.927 1.781,1.927 true 0.5,1.583 0.333,1.417 0.333,1.417 0.25,1.417 true 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.917,0.219 2.229,0.417 0.313,0.198 10 false *b 0.771,0.635 1.083,0.833 0.313,0.198 10 false *1 2.25,0.635 2.563,0.833 0.313,0.198 10 false *1 0.083,1.344 0.396,1.542 0.313,0.198 10 false *3 1.615,1.844 1.927,2.042 0.313,0.198 10 false *3 0.979,1.823 1.292,2.021 0.313,0.198 10 false *2 2.448,1.823 2.76,2.021 0.313,0.198 10 false *2 3.146,1.521 3.365,1.719 0.219,0.198 10 false *4 1.635,0.667 1.948,0.865 0.313,0.198 10 false *4
*1 Air
*2 Port E
*3 Port F
*4 Air Filter
*a Vacuum Switching Valve is On
*b Vacuum Switching Valve is Off


a.

Disconnect the vacuum hose (port F) from the vacuum switching valve assembly (for AICV).


b.

Enter the following menus.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for AICS
50004 372 66

c.

Check the operation of the vacuum switching valve assembly (for AICV) when the vacuum switching valve assembly (for AICV) is operated using the GTS.

Standard:
GTS Connection Specified Condition
ON Air from port E flows out through port F
OFF Air from port E flows out through the air filter



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV)
2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV)
a.

Inspect the vacuum switching valve assembly (for AICV)

Click hereEngine / Hybrid System>G16E-GTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV))

NG

REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV))
a.

Disconnect the vacuum switching valve assembly (for AICV) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D98-2(+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV) - ECM)

NG

5.INSPECT EFI-MAIN NO. 1 RELAY
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV) - ECM)
a.

Disconnect the vacuum switching valve assembly (for AICV) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D98-1(AIRV) - D104-49(AICV) Always Below 1 Ω
D98-1(AIRV) or D104-49(AICV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT EFI-MAIN NO. 1 RELAY
a.

Inspect the EFI-MAIN NO. 1 relay.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI-MAIN NO.1 RELAY)

NG

REPLACE EFI-MAIN NO. 1 RELAY

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI-MAIN NO.1 RELAY)
a.
A468644C04
0.083,0.104 0.396,0.26 0.313,0.156 10 false *1 1.677,2.042 1.99,2.198 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 EFI-MAIN NO. 1 Relay


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 3 relay) - Body ground Always 11 to 14 V
1 (EFI-MAIN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 3 RELAY)

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - VACUUM SWITCHING VALVE ASSEMBLY (FOR AICV))
a.

Remove the EFI-MAIN NO. 1 relay, EFI-MAIN NO. 3 relay and EDU relay from the No. 1 engine room relay block assembly.

HINT:

Remove the EFI-MAIN NO. 3 relay and EDU relay connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Disconnect the vacuum switching valve assembly (for AICV) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5(EFI-MAIN NO.1 relay) - D98-2 (+B) Always Below 1 Ω
5(EFI-MAIN NO.1 relay) or D98-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR