Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P001013  A Camshaft Position Actuator Bank 1 Circuit Open  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The cam timing oil control solenoid assembly (for intake camshaft) operates according to signals received from the ECM to control the position of the camshaft timing oil control valve assembly and supply engine oil. The camshaft timing oil control valve assembly moves when the ECM applies 12 V to the cam timing oil control solenoid assembly (for intake camshaft). The ECM changes the energizing time of the cam timing oil control solenoid assembly (for intake camshaft) duty-cycle in accordance with the camshaft position, crankshaft position, throttle position, etc.

A321256E18
1.615,4.625 1.74,4.083 1.74,4.083 1.885,4.083 false 2.594,4.948 3.083,5.25 3.083,5.25 3.167,5.25 true 2.865,4.719 3.365,4.396 3.365,4.396 3.51,4.396 true 4.083,4.833 4.25,4.667 4.25,4.667 4.417,4.667 true 0.115,0.125 1.344,0.323 1.229,0.198 10 false VVT System: 1.927,1.458 3.448,1.667 1.521,0.208 10 false Actual Valve Timing 1.979,2.156 3.406,2.427 1.427,0.271 10 false Target Valve Timing 2.271,2.896 3.073,3.167 0.802,0.271 10 false Correction 0.26,3.74 1.292,3.979 1.031,0.24 10 false Duty-cycle 1.948,4.021 5.427,4.24 3.479,0.219 10 false Cam Timing Oil Control Solenoid Assembly 3.552,4.333 6.802,4.583 3.25,0.25 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.26,5.188 6.188,5.469 2.927,0.281 10 false Camshaft Timing Oil Control Valve Assembly 4.531,4.583 6.5,4.771 1.969,0.188 10 false Intake Camshaft 5.073,0.74 6.198,1.042 1.125,0.302 10 false VVT Sensor 4.604,1.25 6.344,1.5 1.74,0.25 10 false Crankshaft Position Sensor 4.406,1.76 6.656,2.052 2.25,0.292 10 false Mass Air Flow Meter Sub-assembly 4.698,2.292 6.677,2.594 1.979,0.302 10 false Throttle Position Sensor 4.365,3.063 6.865,3.365 2.5,0.302 10 false Engine Coolant Temperature Sensor 4.771,3.573 6.75,3.875 1.979,0.302 10 false Vehicle Speed Sensor 2.438,3.396 3.115,3.729 0.677,0.333 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001013 A Camshaft Position Actuator Bank 1 Circuit Open Open or short in cam timing oil control solenoid assembly (for intake camshaft of) circuit (1 trip detection logic).
·

Open or short in cam timing oil control solenoid assembly (for intake camshaft of) circuit

·

Cam timing oil control solenoid assembly (for intake camshaft of)

·

ECM


Comes on SAE: P0010

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the cam timing oil control solenoid assembly (for intake camshaft) circuit. If the cam timing oil control solenoid duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Cam timing oil control solenoid assembly (for intake camshaft)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Wait 5 seconds or more [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P001013.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [C] again.




WIRING DIAGRAM

A398294E03
1.781,1.365 1.938,1.563 0.156,0.198 10 false 2 1.781,0.74 1.938,0.938 0.156,0.198 10 false 1 0.49,1.823 0.948,2.021 0.458,0.198 10 false D92 0.469,1.99 2.49,2.49 2.021,0.5 10 false Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) 4.625,0.76 4.885,1.021 0.26,0.26 10 false 27 4.635,1.396 4.958,1.771 0.323,0.375 10 false 28 4.896,0.76 5.51,0.958 0.615,0.198 10 false OC1+ 4.896,1.396 5.51,1.594 0.615,0.198 10 false OC1- 4.917,2.219 5.375,2.417 0.458,0.198 10 false D104 4.917,2.375 6.927,2.583 2.01,0.208 10 false ECM 1.552,1.385 1.708,1.583 0.156,0.198 10 false - 1.531,0.76 1.688,0.958 0.156,0.198 10 false +

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P001013)
a.

Clear the DTC after recording the freeze frame data and DTC.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Start the engine.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001013 is output A
DTCs are not output B




A

2.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

B

2.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the cam timing oil control solenoid assembly (for intake camshaft).

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL SOLENOID>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the cam timing oil control solenoid assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D92-1(+) - D104-27(OC1+) Always Below 1 Ω
D92-2(-) - D104-28(OC1-) Always Below 1 Ω
D92-1(+) or D104-27(OC1+) - Body ground and other terminals Always 10 kΩ or higher
D92-2(-) or D104-28(OC1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR