Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System) › from 2020.09
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0420298 AIR CONDITIONING SYSTEM(for Gasoline Model with Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model with Automatic Air Conditioning System)  B14B287  Lost Communication with Front Panel LIN Missing Message  


DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication.

If a malfunction occurs in the LIN communication system, the air conditioning amplifier assembly will not operate, even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B287 Lost Communication with Front Panel LIN Missing Message Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Error or lost communication with air conditioning control assembly


Detection Time:

Continuously for 10 seconds or more


·

Air conditioning control assembly

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Malfunction Error communication with air conditioning control assembly ○ -
Lost communication with air conditioning control assembly - ○
Detection Time Continuously for 10 seconds or more Continuously for 10 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored.


WIRING DIAGRAM

E441720E01
0.052,2.625 0.51,2.823 0.458,0.198 10 false H31 1.323,0.677 1.781,0.875 0.458,0.198 10 false LIN1 1.375,1.219 1.833,1.417 0.458,0.198 10 false IG+ 1.281,2.167 1.74,2.365 0.458,0.198 10 false GND 2.146,1.802 3.177,2.031 1.031,0.229 10 false ECU-IGP NO. 3 3.302,1.625 4.375,1.896 1.073,0.271 10 false from IGP Relay 5.635,0.688 6.094,0.885 0.458,0.198 10 false LIN1 4.927,2.604 5.292,2.844 0.365,0.24 10 false H24 0.052,2.792 2.24,3.052 2.188,0.26 10 false Air Conditioning Control Assembly 4.927,2.771 7.156,3.115 2.229,0.344 10 false Air Conditioning Amplifier Assembly 0.677,3.365 2.396,3.573 1.719,0.208 10 false : LIN Communication Line 1.698,0.51 1.917,0.74 0.219,0.229 10 false 7 1.708,1.094 1.948,1.292 0.24,0.198 10 false 9 1.677,2.042 1.958,2.271 0.281,0.229 10 false 13 5.448,0.51 5.719,0.792 0.271,0.281 10 false 7 3.313,1.208 5.583,1.573 2.271,0.365 10 false from Engine Stop and Start ECU*1 2.5,3.354 4.531,3.646 2.031,0.292 10 false *1: w/ Stop and Start System 2.156,1.094 2.396,1.292 0.24,0.198 10 false *1 2.156,1.5 2.396,1.698 0.24,0.198 10 false *2 4.635,3.354 6.667,3.646 2.031,0.292 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)

B

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)

Pre-procedure1

a.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H31-9 (IG+) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)

Pre-procedure1

a.

Disconnect the H31 air conditioning control assembly connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H31-9 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H31-13 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H24 air conditioning amplifier assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H31-7 (LIN1) - H24-7 (LIN1) Always Below 1 Ω
H31-7 (LIN1) or H24-7 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

6.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
except G16E-GTS A
for G16E-GTS B



A

7.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

B

9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
7.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

Pre-procedure1

a.

Connect the H24 air conditioning amplifier assembly connector.


Procedure1

b.
E334619N03
0.302,1.563 0.76,1.76 0.458,0.198 10 false GND

Using an oscilloscope, check the waveform.

Item Content
Terminal No. H24-7 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

8.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

NG

8.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

Pre-procedure1

a.

Connect the air conditioning control assembly connector.


Procedure1

b.
E389745C02
1.573,0.094 2.042,0.375 0.469,0.281 0.771,2.094 1.292,1.271 true 1.698,0.167 2.156,0.365 0.458,0.198 10 false H31 0.135,0.115 0.594,0.313 0.458,0.198 10 false *a 0.615,2.135 1.073,2.333 0.458,0.198 10 false LIN1 0.438,3.958 0.896,4.156 0.458,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Control Assembly)


Using an oscilloscope, check the waveform.

Item Content
Terminal No. H31-7 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG

9.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

Pre-procedure1

a.

Connect the H24 air conditioning amplifier assembly connector.


Procedure1

b.
E334619N03
0.302,1.563 0.76,1.76 0.458,0.198 10 false GND

Using an oscilloscope, check the waveform.

Item Content
Terminal No. H24-7 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

10.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

NG

10.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

Pre-procedure1

a.

Connect the air conditioning control assembly connector.


Procedure1

b.
E389745C02
1.573,0.094 2.042,0.375 0.469,0.281 0.771,2.094 1.292,1.271 true 1.698,0.167 2.156,0.365 0.458,0.198 10 false H31 0.135,0.115 0.594,0.313 0.458,0.198 10 false *a 0.615,2.135 1.073,2.333 0.458,0.198 10 false LIN1 0.438,3.958 0.896,4.156 0.458,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Control Assembly)


Using an oscilloscope, check the waveform.

Item Content
Terminal No. H31-7 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

NG