Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK (for 5 Door) › from 2020.09
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0447250 FRONT DOOR LOCK(for 5 Door) A

DOOR LOCK  FRONT DOOR LOCK(for 5 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69760B 1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B584477

Engage the guide to install the front door inside locking cable assembly to the front door lock assembly.


Hide 69760B 2.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

B584480

a.

Engage the guide to install the front door inside locking cable assembly to the front door lock assembly.


Hide 69720D 3.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B584476

Engage the guide to install the front door lock remote control cable assembly to the front door lock assembly.


b.
B584482C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69720D 4.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B584479

Engage the guide to install the front door lock remote control cable assembly to the front door lock assembly.


b.
B584484C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69040A 5.INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
·

When reusing a removed front door lock assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock assembly.


b.

When reusing the front door lock assembly:

i.
B584474

Install a new door lock wiring harness seal to the front door lock assembly.



c.
B584483

Connect the front door lock open rod as shown in the illustration.

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Connect the connector.


Hide 6.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 69220 7.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Hide 67404F 8.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 68151C 9.INSTALL FRONT DOOR GLASS RUN

Hide 68102 10.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 11.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 67856B 12.INSTALL FRONT DOOR PANEL PROTECTOR

Hide 67838A 13.INSTALL FRONT DOOR VENT SEAL

Hide 68172A 14.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 67602 15.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67656 16.INSTALL FRONT DOOR TRIM GARNISH

Hide 74231 17.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Hide 74232 18.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Hide 67492A 19.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 20.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 21. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 22.INITIALIZE POWER WINDOW CONTROL SYSTEM