Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK (for 3 Door) › from 2020.09
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0447251 FRONT DOOR LOCK(for 3 Door) A

DOOR LOCK  FRONT DOOR LOCK(for 3 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69760B 1.INSTALL FRONT DOOR LOCK/UNLOCK KNOB INSIDE LOCKING CABLE (w/o Double Locking System)

a.
B584477

Engage the guide to install the front door lock/unlock knob inside locking cable to the front door with motor lock assembly.


Hide 69760B 2.INSTALL FRONT DOOR LOCK/UNLOCK KNOB INSIDE LOCKING CABLE (w/ Double Locking System)

B584480

a.

Engage the guide to install the front door lock/unlock knob inside locking cable to the front door with motor lock assembly.


Hide 69720D 3.INSTALL FRONT DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE (w/o Double Locking System)

a.
B584476

Engage the guide to install the front door lock open lever remote control cable to the front door with motor lock assembly.


b.
B584482C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69720D 4.INSTALL FRONT DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE (w/ Double Locking System)

a.
B584479

Engage the guide to install the front door lock open lever remote control cable to the front door with motor lock assembly.


b.
B584484

Engage the claws as shown in the illustration.


Hide 69040A 5.INSTALL FRONT DOOR WITH MOTOR LOCK ASSEMBLY

NOTICE:
·

When reusing a removed front door with motor lock assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door with motor lock assembly.



a.

Apply MP grease to the sliding parts of the front door with motor lock assembly.


b.

When reusing the front door with motor lock assembly:

i.
B584474

Install a new door lock wiring harness seal to the front door with motor lock assembly.



c.
B584483

Connect the front door lock open rod as shown in the illustration.

HINT:

Make sure that the front door lock open rod is securely connected to the front door with motor lock assembly.



d.

Using a T30 "TORX" socket wrench, install the front door with motor lock assembly with the 3 screws.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Connect the connector.


Hide 6.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 69220 7.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Hide 67832 8.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 68172A 9.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 67602 10.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67656 11.INSTALL FRONT DOOR TRIM GARNISH

Hide 74231 12.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Hide 74232 13.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Hide 67492A 14.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 15.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 16. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART