Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for 3 Door) › from 2020.09
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0447487 FRONT DOOR(for 3 Door) A

DOOR / HATCH  FRONT DOOR(for 3 Door)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
B595576

Install the 2 hole plugs.


Hide 2.INSTALL HOLE PLUG

a.
B595574

Install the 3 hole plugs.


Hide 67837B 3.INSTALL FRONT DOOR DUST PROOF SEAL

a.
B595571

Engage the claws to install 3 new front door dust proof seals.


Hide 4.INSTALL CUSHION

a.
B595570

Engage the claws to install 2 new cushions.


Hide 67862 5.INSTALL FRONT DOOR WEATHERSTRIP

a.
B595131C01
0.042,1.052 0.208,1.219 0.167,0.167 10 true *a 0.063,0.156 0.229,0.323 0.167,0.167 10 true *a 0.969,0.719 1.135,0.885 0.167,0.167 10 true *a
*a Clip (A)


Engage the 3 clips (A) and other clips to install the front door weatherstrip.


Hide 6.INSTALL FRONT DOOR DIVISION BAR SEAL

a.
B595130

Install the front door division bar seal.


b.

Engage the 3 clips.


Hide 68620 7.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt A.


c.

Apply adhesive to the threads of the bolt A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B584263C01
2.188,1.365 2.396,1.563 0.208,0.198 10 true *a 1.646,1.323 1.833,1.542 0.188,0.219 10 true *b 1.656,0.573 1.854,0.781 0.198,0.208 10 true *b
*a Bolt A
*b Bolt B


Install the front door check assembly with the bolt A and 2 bolts B.

Torque:
Bolt A : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68210C 8.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 69312 9.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B584271C01
2.844,2.073 2.51,2.417 true 2.896,1.948 3.208,2.146 0.313,0.198 10 false *a
*a Snap
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the snap to install the front door lock open rod to the front door outside frame sub-assembly as shown in the illustration.


Hide 69202A 10.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B584272C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the front door outside handle frame sub-assembly as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

w/ Entry and Start System:

i.
B584260

Engage the clamp to install the wire harness.



Hide 69040A 11.INSTALL FRONT DOOR WITH MOTOR LOCK ASSEMBLY

Hide 69242E 12.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B584259

Engage the guides to install the front door outside handle rear pad.


Hide 69241H 13.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B584258

Engage the guide and claws to install the front door outside handle front pad.


Hide 14.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B584255

Install the front door lock cylinder assembly.

HINT:

Check that the front door lock cylinder assembly is inserted into the front door lock with motor assembly.



b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B584254

Install the hole plug.


Hide 69217F 15.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B584257

Engage the claws and guides to install the front door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B584256

Install the hole plug.


Hide 69220 16.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B584273C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door outside handle assembly as shown in the illustration.


b.
B563133

Move the lever and engage the claws as shown in the illustration.


c.

w/ Entry andStart System:

i.
B563134

Connect the connector.


ii.

Engage the claws.



Hide 67402F 17.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B595129C01
1.635,0.469 2.313,0.469 true 1.875,1.5 2.458,1.5 true 1.354,0.365 1.583,0.563 0.229,0.198 10 true *a 1.583,1.417 1.802,1.604 0.219,0.188 10 true *b
*a Bolt
*b Nut


Install the front door front lower frame sub-assembly with the bolt A and bolt B.

Torque:
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Nut : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68151C 18.INSTALL FRONT DOOR GLASS RUN

a.
B595128

Install the front door glass run.


Hide 19.INSTALL DOOR GLASS FEMALE STABILIZER

a.
B595126

Engage the guide to install the door glass female stabilizer.


b.

Install the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 20.INSTALL FRONT DOOR UPPER WINDOW STOP

a.
B595125

Engage the guides to remove the 2 front door upper window stops.


b.

Install the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 69820 21.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B595142

Using a 4.0 mm hexagon wrench, adjust the 2 stud bolts at the bottom of the front door window regulator assembly as shown in the illustration.

Standard Clearance:
Area Specified Condition
A 20.9 to 21.9 mm (0.823 to 0.862 in.)



b.

Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly LH.


c.
B595127C02
2.646,1.417 3.063,1.552 3.063,1.552 3.063,1.031 true 1.073,1.958 1.302,2.125 0.229,0.167 10 true *a 1.813,0.76 2.042,0.927 0.229,0.167 10 true *b 3,1.573 3.229,1.74 0.229,0.167 10 true *b 2.323,1.979 2.552,2.146 0.229,0.167 10 true *a
*a Nut (A)
*b Nut (B)
V100135

Nut
V100136

Connector


Temporarily install the front door window regulator assembly with the 7 nuts.


d.

Connect the connector.


e.

Tighten the 2 nuts (A) and 3 nuts (B).

Torque:
Nut (A) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Nut (B) : 13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 68102 22.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

for Driver Side:

i.

Connect the multiplex network master switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the multiplex network master switch assembly.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the power window regulator switch assembly.



c.
B595136C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

NOTICE:

Be careful not to damage the front door glass sub-assembly.



d.

Install the front door glass sub-assembly with the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 23.INSTALL WINDOW REGULATOR SHIM

a.
B595122

Install the 2 window regulator shims.


b.

Tighten the 2 nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 24.INSPECT FRONT DOOR GLASS SUB-ASSEMBLY

B595140N01
1.688,2.281 1.844,2.479 0.156,0.198 10 false A 1.406,2.958 1.563,3.156 0.156,0.198 10 false B 0.438,2.635 0.594,2.833 0.156,0.198 10 true C 2.563,0.573 2.719,0.771 0.156,0.198 10 false D 2.323,1.302 2.479,1.5 0.156,0.198 10 false E 4.542,0.521 4.698,0.708 0.156,0.188 10 false G 4.365,1.271 4.521,1.458 0.156,0.188 10 false H 3.365,1.115 3.469,1.313 0.104,0.198 10 true I 5.135,1.052 5.292,1.24 0.156,0.188 10 false J 6.031,0.25 6.188,0.438 0.156,0.188 10 false K 6.167,2.313 6.323,2.5 0.156,0.188 10 false N 5.26,3.083 5.417,3.271 0.156,0.188 10 false M 6.5,0.479 6.656,0.667 0.156,0.188 10 false L 6.677,2.542 6.833,2.729 0.156,0.188 10 false O 1.354,1.094 1.5,1.26 0.146,0.167 10 true F

Standard Clearance:
A 9.2 to 13.2 mm (0.362 to 0.520 in.) B 6.4 to 10.4 mm (0.252 to 0.409 in.)
C 15.0 mm (0.591 in.) D 8.4 to 12.4 mm (0.331 to 0.488 in.)
E 6.4 to 10.4 mm (0.252 to 0.409 in.) F 15.0 mm (0.591 in.)
G 8.4 to 12.4 mm (0.331 to 0.488 in.) H 6.4 to 10.4 mm (0.252 to 0.409 in.)
I 15.0 mm (0.5906 in.) J 30.4 mm (1.197 in.)
K 10.0 to 14.0 mm (0.394 to 0.551 in.) L -2.0 mm to 2.0 mm (-0.079 in to 0.079 in.)
M 30.4 mm (1.197 in.) N 10.0 to 14.0 mm (0.394 to 0.551 in.)
O -2.0 mm to 2.0 mm (-0.079 in to 0.079 in.) - -


Hide 25.ADJUST FRONT DOOR GLASS SUB-ASSEMBLY

a.

Adjust the fit of the top part of the front door glass sub-assembly inward and outward.

i.
B595141

Loosen the 2 nuts at the bottom of the front door window regulator assembly.


ii.

Using a 4.0 mm hexagon wrench, turn the 2 stud bolts to adjust the fit of the top part of the front door glass sub-assembly inward and outward.

HINT:

When the stud bolt are turned counterclockwise, the top part of the front door glass sub-assembly moves toward the inside of the vehicle. When the stud bolt are turned clockwise, the top part of the front door glass sub-assembly moves toward the outside of the vehicle.



iii.

Tighten the 2 nuts after adjustment.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.

Adjust the fit of the bottom part of the front door glass sub-assembly inward and outward.

i.
B595122

Loosen the 2 nuts at the top of the front door window regulator assembly.


ii.

Change the number of installed window regulator shims to adjust the fit of the bottom part of the front door glass sub-assembly inward and outward.

HINT:
·

When more shims are used, the bottom part of the front door glass sub-assembly moves toward the outside of the vehicle. When less shims are used, the bottom part of the front door glass sub-assembly moves toward the inside of the vehicle.

·

The thickness of one window regulator shim is 1.0 mm (0.039 in.).




iii.

Tighten the 2 nuts after adjustment.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)



c.

Connect the cable to the negative (-) battery terminal.


d.

for Driver Side:

Connect the multiplex network master switch assembly.


e.

for Front Passenger Side:

Connect the power window regulator switch assembly.


f.
B595549C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Adjust the front door glass sub-assembly fully closed position horizontally and vertically.

i.

Loosen the 2 front door upper window stop bolts and temporarily move the front door upper window stops to the top of their adjustment range and then temporarily install the bolts.


ii.

Loosen the 3 front door glass sub-assembly nuts.


iii.

Stop the front door glass sub-assembly approximately 3 mm (0.118 in.) below the fully closed position.


iv.

While holding the front door glass sub-assembly, move it vertically and horizontally to adjust its position.


v.

Tighten the 3 nuts after adjustment.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


vi.

Move the front door glass sub-assembly to the fully closed position.


vii.

Loosen the 2 front door upper window stop bolts.


viii.

While lightly pushing each front door upper window stop against the stopper on the front door glass sub-assembly, tighten each bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)



g.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.



h.

for Driver Side:

Disconnect the multiplex network master switch assembly.


i.

for Front Passenger Side:

Disconnect the power window regulator switch assembly.


Hide 26.INSTALL HOLE SEAL

a.
B595573

Install the 2 hole seals.


Hide 27.INSTALL HOLE SEAL

a.
B595572

Install the 2 hole seals.


Hide 28.INSTALL HOLE PLUG

a.
B595575

Install the 4 hole plugs.


Hide 67832 30.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B595120

Pass the front door lock open lever remote control cable, front door lock/unlock knob inside locking cable and wire harness through front door service hole cover.


b.

Engage the clips to install the front door service hole cover.


c.
B595137C01
0.229,1.146 0.385,0.927 true 1.063,1.292 1.219,1.073 true 1.344,1.563 1.5,1.344 true 1.24,1.615 1.458,1.833 0.219,0.219 10 true *b 0.813,1.198 1.021,1.417 0.208,0.219 10 true *a 0.115,1.177 0.333,1.396 0.219,0.219 10 true *b
*a Clamp
*b Guide


Engage the clamp and guides.


d.

Insert the 3 front door service hole cover clips and turn them 45° as shown in the illustration.


Hide 87940 31.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 86262E 32.INSTALL NO. 1 FRONT SPEAKER BRACKET

a.
B594356

Install the No. 1 front speaker bracket with the 3 screws.


b.

Engage the guide.


Hide 86160 33.INSTALL NO. 1 FRONT SPEAKER ASSEMBLY

Hide 68172A 34.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B595138

Install the front door glass inner weatherstrip.


Hide 69284C 35.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B584238

Engage the claw to install the front door inside handle bezel plug.


Hide 69206B 36.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B584237

Engage the guides to install the front door inside handle sub-assembly.


Hide 37.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Interior Illumination)

a.
B595143

Engage the claws to install the No. 1 interior illumination light assembly.


Hide 67602 38.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B584277C01
2.563,1.719 2.135,1.229 true 2.573,0.552 2.104,0.979 true 2.625,0.427 2.865,0.646 0.24,0.219 10 true *1 2.604,1.646 2.844,1.885 0.24,0.24 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Engage the guides to connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.
B595139C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws and clips to install the front door trim board sub-assembly as shown in the illustration.


c.

Install the 3 screws.


d.
B564984

Engage the claw to close the front door inside handle bezel plug.


Hide 67656 39.INSTALL FRONT DOOR TRIM GARNISH

a.
B584278C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front door trim garnish as shown in the illustration.


b.

Install the screw.


Hide 74232 40.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

a.

Connect the 2 connectors.


b.
B584227

Engage the claws and guides to install the multiplex network master switch assembly with front door upper armrest base panel.


Hide 74231 41.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B584229

Engage the claws and guides to install the power window regulator switch assembly with front door upper armrest base panel.


Hide 67492A 42.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B594352

Engage the claws and clip to install the front door lower frame bracket garnish.


Hide 43.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 44. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 46.INITIALIZE POWER WINDOW CONTROL SYSTEM