Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › from 2020.09
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0422050 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system

·

Parking support brake system


(Click here)

PROCEDURE

Hide 89348N 2.REMOVE NO. 1 ULTRASONIC SENSOR CLIP

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E436550

Disengage the wire harness clamp.


b.
E436551C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the No. 1 ultrasonic sensor clip as shown in the illustration.


Hide 89341K 3.REMOVE FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.

for 5 Door:

i.
E436537C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


ii.

Disengage the claws to remove the front corner ultrasonic sensor as shown in the illustration.



b.

for 3 Door:

i.
E450583C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


ii.

Disengage the claws to remove the front corner ultrasonic sensor as shown in the illustration.



Hide 89341L 4.REMOVE FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.

for 5 Door:

i.
E436538C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


ii.

Disengage the claws to remove the front center ultrasonic sensor as shown in the illustration.



b.

for 3 Door:

i.
E450584C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


ii.

Disengage the claws to remove the front center ultrasonic sensor as shown in the illustration.



Hide 89347B 5.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (for 5 Door)

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E436539

Remove the front corner ultrasonic sensor retainer.


Hide 89347B 6.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (for 3 Door)

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E450585

Remove the front corner ultrasonic sensor retainer.