Home › Drivetrain › CLUTCH › CLUTCH STROKE SENSOR (for LHD) › from 2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0447596 CLUTCH STROKE SENSOR(for LHD) A

CLUTCH  CLUTCH STROKE SENSOR(for LHD)  INSTALLATION  


PROCEDURE

Hide 89280 1.INSTALL CLUTCH PEDAL STROKE SENSOR ASSEMBLY

a.

When installing a new clutch pedal stroke sensor assembly:

NOTICE:

Do not break the clutch pedal stroke sensor assembly lever set pin before being instructed to do so.


i.
C440378C01
2.521,0.75 2.865,0.708 true 0.969,3.594 1.094,3.594 1.094,3.594 1.146,3.917 true 1.135,4.052 1.177,4.281 1.177,4.281 1.302,4.281 true 0.75,3.5 0.969,3.698 0.219,0.198 10 true *a 1.313,4.177 1.531,4.375 0.219,0.198 10 true *b 2.885,0.594 3.104,0.792 0.219,0.198 10 true *c
*a Clutch Pedal Stroke Sensor Assembly Lever
*b Clutch Pedal Groove
*c Clutch Pedal Stroke Sensor Assembly Lever Set Pin


Install a new clutch pedal stroke sensor assembly to the clutch pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the clutch pedal stroke sensor assembly lever with the clutch pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the clutch pedal stroke sensor assembly.

·

Check that the tip of the clutch pedal stroke sensor assembly lever is protruding from the clutch pedal groove.

·

Do not drop the clutch pedal stroke sensor assembly.

·

If the clutch pedal stroke sensor assembly has been dropped, replace the clutch pedal stroke sensor assembly with a new one.

·

Do not subject the clutch pedal stroke sensor assembly to shock during installation.

·

Make sure to confirm that the clutch pedal fully returns to its original position.




ii.

Connect the clutch pedal stroke sensor assembly connector.


iii.

Firmly depress the clutch pedal sub-assembly to break the clutch pedal stroke sensor assembly lever set pin.


iv.

Remove the broken clutch pedal stroke sensor assembly lever set pin.



b.

When reusing the clutch pedal stroke sensor assembly:

i.
C440388C01
1.229,2.74 1.146,2.417 1.146,2.417 1,2.417 true 1.208,2.865 1.281,3.125 1.281,3.125 1.417,3.125 true 0.781,2.323 0.99,2.51 0.208,0.188 10 true *a 1.438,3.031 1.646,3.219 0.208,0.188 10 true *b
*a Clutch Pedal Stroke Sensor Assembly Lever
*b Clutch Pedal Groove


Install the clutch pedal stroke sensor assembly to the clutch pedal support assembly and temporarily tighten the 2 nuts.

NOTICE:
·

Engage the clutch pedal stroke sensor assembly lever with the clutch pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the clutch pedal stroke sensor assembly.

·

Check that the tip of the clutch pedal stroke sensor assembly lever is protruding from the clutch pedal groove.

·

Do not drop the clutch pedal stroke sensor assembly.

·

If the clutch pedal stroke sensor assembly has been dropped, replace the clutch pedal stroke sensor assembly with a new one.

·

Do not subject the clutch pedal stroke sensor assembly to shock during installation.

·

Make sure to confirm that the clutch pedal fully returns to its original position.



HINT:

When fully tightening the nuts, perform Adjust Clutch Pedal Stroke Sensor Assembly first.



ii.

Connect the clutch pedal stroke sensor assembly connector.



Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89280 3.ADJUST CLUTCH PEDAL STROKE SENSOR ASSEMBLY

NOTICE:

When the clutch pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.


a.

Connect the GTS to the DLC3 with the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Clutch Stroke Sensor Voltage.

Powertrain > Engine > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 372 607

e.
C440380

Read the stroke sensor value in the Data List, and turn the clutch pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (clutch pedal fully released):

0.96 to 1.04 V



f.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

After turning the ignition switch to ON, do not depress the clutch pedal sub-assembly until the nuts have been tightened.



g.

Turn the GTS off and turn the ignition switch off.


h.

Disconnect the GTS from the DLC3.


Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 7. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART