Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD) › from 2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0430794 CLUTCH PEDAL(for LHD) A

CLUTCH  CLUTCH PEDAL(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the clutch pedal support assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for G16E-GTS)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
for G16E-GTS

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for G16E-GTS)

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 55606 1.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 84520 2.REMOVE CLUTCH START SWITCH ASSEMBLY

Hide 31453A 3.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

a.
C446878

Remove the clip from the clevis pin.


b.

Remove the master cylinder push rod clevis with hole pin to disconnect the clutch master cylinder assembly from the clutch pedal sub-assembly.


Hide 55107A 4.REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY

a.

for G16-GTS:

i.
C446901

Disconnect the clutch pedal stroke sensor assembly connector.


ii.

Disengage the clamp to disconnect the wire harness from the clutch pedal support assembly.


iii.
C446880

Remove the 4 nuts and clutch pedal support assembly from the vehicle body.



b.

except G16-GTS:

i.
C437868

Disconnect the clutch switch assembly connector.


ii.

Disengage the 2 clamps to disconnect the wire harness from the clutch pedal support assembly.


iii.
C437869

Remove the 4 nuts and clutch pedal support assembly from the vehicle body.



Hide 89280 5.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY (for G16E-GTS)

Hide 88280A 6.REMOVE CLUTCH SWITCH ASSEMBLY (except G16E-GTS)

Hide 31316 7.REMOVE TURN OVER CLUTCH PEDAL SPRING

a.
C446881

Remove the turn over clutch pedal spring from the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.

NOTICE:

Do not damage the turn over clutch pedal spring.



Hide 31353 8.REMOVE CLUTCH PEDAL SPRING HOLDER

a.
C446882

Remove the clutch pedal spring holder from the clutch pedal sub-assembly.


Hide 31395A 9.REMOVE NO. 1 PEDAL SPRING HOOK

a.
C450360

Remove the 2 No. 1 pedal spring hooks from the clutch pedal bracket sub-assembly.


Hide 31321 10.REMOVE CLUTCH PEDAL PAD

a.
C446884

Remove the clutch pedal pad from the clutch pedal sub-assembly.