The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel sub-assembly removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. TABLE OF BOLT, SCREW AND NUT
All bolts and screws relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
for G16E-GTS:
Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>REMOVAL
for 1KR-FE:
Click hereGeneral>MAINTENANCE>1KR-FE AUXILIARY BATTERY>REMOVAL
4.REMOVE REAR CONSOLE BOX ASSEMBLY
for 5 Door:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX (for 5 Door)>REMOVAL
for 3 Door:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX (for 3 Door)>REMOVAL
5.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
67914B
6.REMOVE FRONT DOOR SCUFF PLATE LH
for 5 Door:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL
for 3 Door:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL
67913B
7.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62112
8.REMOVE COWL SIDE TRIM BOARD LH
for 5 Door:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL
for 3 Door:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL
62111C
9.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
55606
10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the 2 screws <A>.
Disengage the claws and guide to remove the No. 1 instrument panel under cover sub-assembly as shown in the illustration.
55607
11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claws and guide to remove the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
62312B
12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for 5 Door)
Disconnect the front door opening trim weatherstrip LH from the area shown in the illustration.
62311B
13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for 5 Door)
Use the same procedure as for the LH side.
63376B
14.DISCONNECT NO. 1 ROOF HEADLINING MOULDING LH (for 3 Door)
Disconnect the No. 1 roof headlining moulding LH from the area shown in the illustration.
63375B
15.DISCONNECT NO. 1 ROOF HEADLINING MOULDING RH (for 3 Door)
Use the same procedure as for the LH side.
62312B
16.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for 3 Door)
Disconnect the front door opening trim weatherstrip LH from the area shown in the illustration.
62311B
17.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for 3 Door)
Use the same procedure as for the LH side.
55317E
18.REMOVE NO. 1 INSTRUMENT SIDE PANEL
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a molding remover A, disengage the clips and guides to remove the No. 1 instrument side panel as shown in the illustration.
for Front Passenger Side with Airbag Cut off Switch:
Disconnect the connector.
55318F
19.REMOVE NO. 2 INSTRUMENT SIDE PANEL
Use the same procedure as for the No. 1 side.
55550
20.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
| *a | Stopper |
|
Push |
Disengage the 2 stoppers and pull out the glove compartment door assembly until it is level.
Disengage the claw to separate the glove compartment door stopper sub-assembly from the glove compartment door assembly.
|
Remove in this Direction |
Disengage the hinges to remove the glove compartment door assembly as shown in the illustration.
55054
21.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
Disengage the claw to remove the glove compartment door stopper sub-assembly.
55433B
22.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Remove the 2 screws <C>, 3 screws <D> and screw <E>.
|
Remove in this Direction |
Disengage the claws and guides to remove the lower No. 2 instrument panel finish panel as shown in the illustration.
55557A
23.REMOVE GLOVE COMPARTMENT DOOR CHECK CUSHION
Use the same procedure as for the opposite side.
Disengage the claws to remove the glove compartment door check cushion.
62212
24.REMOVE FRONT PILLAR GARNISH LH
|
Pull up |
Pull up the front pillar garnish LH to disengage the front pillar garnish clip and clip as shown in the illustration.
| *a | Release Lever |
|
Push |
Push the release lever and separate the front pillar garnish clip from the vehicle body as shown in the illustration.
When the front pillar garnish clip cannot be removed using your fingers:
|
Lift in this Direction |
While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow shown in the illustration.
|
Remove in this Direction |
While pulling the front pillar garnish clip in the direction indicated by the arrow, push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.
|
Remove in this Direction |
Disengage the guides as shown in the illustration.
w/ Speaker:
Disengage the claws to disconnect the front No.2 speaker assembly and remove the front pillar garnish LH.
w/o Speaker:
Disengage the clamp to remove the front pillar garnish LH.
Remove the front pillar garnish clip from the front pillar garnish LH.
| *a | Protective Cover |
|
Adhesive Tape |
Protect the curtain shield airbag assembly.
Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.
Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.
62211
25.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
86160P
26.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for 6 or 8 Speakers)
53601
27.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the claw and guides to disconnect the hood lock control lever sub-assembly.
55480D
28.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
|
Remove in this Direction |
Remove the bolt <F>.
Disengage the clips, claw and guide to remove the lower instrument panel finish panel assembly as shown in the illustration.
Disconnect each connector.
55548A
29.REMOVE INSTRUMENT PANEL HOLE COVER (w/ Cover)
Remove the 2 screws <A>.
Disengage the guides to remove the instrument panel hole cover.
55410C
30.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Analog Meter)
Remove the 2 screws <A> or 2 screws <B>.
|
Remove in this Direction |
Disengage the clips, claws and guides to remove the instrument cluster finish panel assembly as shown in the illustration.
55410C
31.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Digital Meter)
Remove the 2 screws <A> or 2 screws <B>.
|
Remove in this Direction |
Disengage the clips, claws and guides to remove the instrument cluster finish panel assembly as shown in the illustration.
83100
32.REMOVE COMBINATION METER ASSEMBLY (for Analog Meter)
83100
33.REMOVE COMBINATION METER ASSEMBLY (for Digital Meter)
55406B
34.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
55900
35.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
55405B
36.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUBASSEMBLY (w/ Audio)
|
Remove in this Direction |
Disengage the clips, claws and guides to remove the instrument cluster finish center panel sub-assembly as shown in the illustration.
Disconnect the connector.
55670A
37.REMOVE INSTRUMENT PANEL CENTER REGISTER ASSEMBLY
|
Protective Tape |
Apply protective tape to the locations shown in the illustration.
|
Remove in this Direction |
Disengage the clips and guides as shown in the illustration.
Disengage the clamp to remove the instrument panel center register assembly.
86140A
38.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Audio)
55420A
39.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY (w/ Audio)
|
Remove in this Direction |
Disengage the clips to remove the instrument cluster finish center panel assembly as shown in the illustration.
55405B
40.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL ASSEMBLY (w/o Audio)
|
Remove in this Direction |
Disengage the clips and claws to remove the instrument cluster finish center panel assembly as shown in the illustration.
55624A
41.REMOVE INSTRUMENT PANEL CENTER TRAY
|
Remove in this Direction |
Disengage the claws to remove the instrument panel center tray as shown in the illustration.
55414A
42.REMOVE INSTRUMENT CLUSTER FINISH END PANEL (w/ Headup Display)
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a molding remover A, disengage the claws and guides to remove the instrument cluster finish end panel as shown in the illustration.
55408F
43.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 8 Speakers)
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a molding remover A, disengage the 5 claws and 2 guides to remove the No. 1 instrument panel speaker sub-assembly as shown in the illustration.
55409F
44.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (for 8 Speakers)
Use the same procedure as for the No. 1 side.
55510F
45.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY (w/ Telematics Transceiver)
|
Protective Tape |
Using a molding remover A, disengage the 4 clips to remove the No. 1 speaker opening cover assembly as shown in the illustration.
86160J
46.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (w/ Telematics Transceiver)
55313A
47.REMOVE INSTRUMENT MAIN PANEL (for Separate Type)
Using a molding remover B, disengage the clips and claws as shown in the illustration.
|
Protective Tape |
|
Remove in this Direction |
Disconnect the connectors.
|
Remove in this Direction | - | - |
Disengage the guides to remove the instrument main panel as shown in the illustration.
86160L
48.REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 8 Speakers)
55302C
49.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for Integrated Type)
Disconnect the connector.
| *a | Airbag Connector | *b | Airbag Bolt |
Remove the bolt <H> and disengage the guide to separate the ground bracket.
Remove the 2 bolts <G>.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Remove the 4 clips.
Disengage the hooks.
Remove the 3 bolts <F>, screw <E> and nut <I> as shown in the illustration.
Disengage the guides to remove the instrument panel sub-assembly as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
55302C
50.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for Separate Type)
Disconnect the connector.
| *a | Airbag Connector | *b | Airbag Bolt |
Remove the bolt <H> and disengage the guide to separate the ground bracket.
Remove the 2 bolts <G>.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Remove the 4 clips.
Disengage the hooks.
Remove the 5 bolts <F>, screw <E> and nut <I> as shown in the illustration.
Disengage the guides to remove the instrument panel sub-assembly as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
55950G
51.REMOVE DEFROSTER NOZZLE ASSEMBLY (for Separate Type)
Remove the 3 screws <A>.
Disengage the guides to remove the defroster nozzle assembly.
89120A
52.REMOVE AUTOMATIC LIGHT CONTROL SENSOR (for Separate Type)
55328
53.REMOVE NO. 1 INSTRUMENT PANEL PIN (for Separate Type)
Use the same procedure as for the opposite side.
Remove the screw <A>.
Disengage the guide to remove the No. 1 instrument panel pin.