The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the clutch pedal sub-assembly removal/installation are shown below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1.REMOVE STEERING COLUMN ASSEMBLY
84520
2.REMOVE CLUTCH START SWITCH ASSEMBLY
31301F
3.REMOVE CLUTCH PEDAL STOPPER BOLT (for G16E-GTS)
| *1 | Clutch Pedal Stopper Bolt |
| *2 | Clutch Pedal Stopper Nut |
Loosen the clutch pedal stopper nut.
Remove the clutch pedal stopper bolt from the clutch pedal sub-assembly.
31453A
4.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN
Remove the clip from the clevis pin.
Remove the master cylinder push rod clevis with hole pin to disconnect the clutch master cylinder assembly from the clutch pedal sub-assembly.
5.REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY
for G16-GTS:
Disconnect the clutch pedal stroke sensor assembly connector.
Disengage the clamp to disconnect the wire harness from the clutch pedal support assembly.
Remove the 4 nuts and clutch pedal support assembly from the vehicle body.
except G16-GTS:
Disconnect the clutch switch assembly connector.
Disengage the 2 clamps to disconnect the wire harness from the clutch pedal support assembly.
Remove the 4 nuts and clutch pedal support assembly from the vehicle body.
89280
6.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY (for G16E-GTS)
88280A
7.REMOVE CLUTCH SWITCH ASSEMBLY (except G16E-GTS)
31301A
8.REMOVE CLUTCH PEDAL SPRING (except 1KR-FE)
Move the clutch pedal sub-assembly to the full stroke position.
Remove the clutch pedal spring from the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.
31301
9.REMOVE CLUTCH PEDAL SUB-ASSEMBLY
Mount the clutch pedal sub-assembly in a soft jaw vise.
Be careful not to damage the clutch pedal sub-assembly in the vise.
Remove the bolt, nut, clutch pedal sub-assembly from the clutch pedal support sub-assembly.
31353
10.REMOVE CLUTCH PEDAL SPRING HOLDER (except 1KR-FE)
Remove the clutch pedal spring holder from the clutch pedal support sub-assembly.
31301P
11.REMOVE CLUTCH PEDAL TURNOVER BUSH (except 1KR-FE)
Remove the clutch pedal turnover bushing from the clutch pedal sub-assembly.
31324A
12.REMOVE CLUTCH PEDAL SHAFT COLLAR
Remove the 2 clutch pedal bushings from the clutch pedal sub-assembly.
Remove the clutch pedal shaft collar from the clutch pedal sub-assembly.
31453B
13.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING
for G16-GTS:
| *1 | Clutch Master Cylinder Push Rod Clevis Bushing |
Using SST and a hammer, remove the clutch master cylinder push rod clevis bushing from the clutch pedal sub-assembly.
except G16-GTS:
| *1 | Clutch Master Cylinder Push Rod Clevis Bushing |
Using SST and a hammer, remove the clutch master cylinder push rod clevis bushing from the clutch pedal sub-assembly.
31321
14.REMOVE CLUTCH PEDAL PAD
Remove the clutch pedal pad from the clutch pedal sub-assembly.