Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0434686 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B276F87  Intrusion Sensor 1 Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and Intrusion sensor stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B276F87 Intrusion Sensor 1 Missing Message No communication between the main body ECU (multiplex network body ECU) and intrusion sensor for 10 seconds or more.
·

Theft warning ultrasonic sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E452937E01
5.854,1.083 6.469,1.281 0.615,0.198 10 false LIN4 5.49,1.719 7.115,2.25 1.625,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,1.542 6.104,1.74 0.615,0.198 10 false H5 5.531,0.896 6.146,1.094 0.615,0.198 10 false 11 3.292,1.771 4.469,2.052 1.177,0.281 10 false Rain Sensor*1 2.938,4.229 4.635,4.5 1.698,0.271 10 false *1: w/ Rain Sensor 0.75,4.24 2.708,4.51 1.958,0.271 10 false : LIN Communication Line 3.292,1.604 3.906,1.802 0.615,0.198 10 false V9 3.781,1.073 4.396,1.271 0.615,0.198 10 false MPX 4.219,0.906 4.833,1.104 0.615,0.198 10 false 3 3.813,2.469 4.427,2.667 0.615,0.198 10 false LIN1 3.792,2.906 4.406,3.104 0.615,0.198 10 false GND 4.198,2.781 4.813,2.979 0.615,0.198 10 false 3 4.198,2.313 4.813,2.51 0.615,0.198 10 false 2 3.052,2.573 3.667,2.771 0.615,0.198 10 false 1 3.26,2.688 3.875,2.885 0.615,0.198 10 false +B 3.125,3.188 3.74,3.385 0.615,0.198 10 false V14 3.135,3.375 5.073,3.792 1.938,0.417 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 1.958,2.823 3.135,3.104 1.177,0.281 10 false ECU-DDC NO. 2 0.135,2.667 1.667,3.042 1.531,0.375 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*1

·

If DTC B276C88 is output, troubleshoot for DTC B276C88 first.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B276C88

*1: w/ Entry and Start System




PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
B276F87 is output A
B276F87 and B127987 are output B



A

2.CHECK HARNESS AND CONNECTOR (INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) - BATTERY AND BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
2.CHECK HARNESS AND CONNECTOR (INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) - BATTERY AND BODY GROUND)
a.

Disconnect the V14 intrusion sensor (theft warning ultrasonic sensor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V14-1 (+B) - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the V14 intrusion sensor (theft warning ultrasonic sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-11 (LIN4) - V14-2 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the V14 intrusion sensor (theft warning ultrasonic sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-11 (LIN4) - V14-2 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR