Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447816 CYLINDER BLOCK G

G16E-GTS ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER BLOCK FOR WARPAGE

a.
A478726

Using a precision straightedge and feeler gauge, check the surface which contacts the cylinder head gasket for warpage.

Maximum Warpage:

0.05 mm (0.00197 in.)


HINT:

If the warpage is more than the maximum, replace the cylinder block sub-assembly.



Hide 2.INSPECT CYLINDER BORE

a.
A478727C02
1.771,3.281 2.188,3.167 true 1.24,3.708 1.583,3.458 true 2.208,3.052 2.521,3.208 0.313,0.156 10 false *a 1.063,3.615 1.375,3.771 0.313,0.156 10 false *b 2.198,3.583 2.51,3.74 0.313,0.156 10 false *c 1.198,4.115 1.51,4.271 0.313,0.156 10 false *d 1.719,3.99 2.031,4.146 0.313,0.156 10 false A 1.719,4.219 2.031,4.375 0.313,0.156 10 false B
*a Thrust Direction
*b Axial Direction
*c 10 mm (0.394 in.)
*d Center
V100135

Front of Engine


Using a cylinder gauge, measure the cylinder bore diameter at the positions (A) and (B) in the thrust and axial directions.

Reference Diameter (New Parts):

87.500 to 87.513 mm (3.4449 to 3.4454 in.)


Maximum Diameter:

87.514 mm (3.4454 in.)


HINT:

If the average diameter of 4 positions is more than the maximum, replace the cylinder block sub-assembly.



Hide 3.INSPECT PISTON

a.
A400516

Using a gasket scraper, remove any carbon from the piston top.


b.
A400517

Using a groove cleaning tool or a broken ring, clean the piston ring grooves.


c.
A400518

Using a brush and solvent, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



d.
A400519C01
0.26,1.573 0.573,1.771 0.313,0.198 10 false *a
*a Distance


Using a micrometer, measure the piston diameter at a right angle to the piston center line where the distance from the bottom of the piston is as specified.

Distance:

10.5 mm (0.413 in.)


Standard Piston Diameter (New Parts):

87.459 to 87.471 mm (3.443 to 3.444 in.)


HINT:

If the diameter is less than the minimum, replace the piston and piston pin as a set.



Hide 4.INSPECT PISTON OIL CLEARANCE

a.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Reference Oil Clearance (New Parts):

0.029 to 0.054 mm (0.00114 to 0.00213 in.)


Maximum Oil Clearance:

0.065 mm (0.00256 in.)


HINT:

If the piston oil clearance is more than the maximum, replace all the pistons with piston pins. If necessary, replace the cylinder block sub-assembly.



Hide 5.INSPECT RING GROOVE CLEARANCE

a.
A400520

Using a feeler gauge, measure the clearance between a new piston ring set and the wall of the ring groove.

Standard Ring Groove Clearance:
Item Specified Condition
No. 1 compression ring 0.045 to 0.075 mm (0.00177 to 0.00295 in.)
No. 2 compression ring 0.020 to 0.070 mm (0.000787 to 0.002756 in.)
Oil ring 0.07 to 0.12 mm (0.00276 to 0.00472 in.)


HINT:

If the groove clearance is not as specified, replace the piston and piston pin as a set.



Hide 6.INSPECT PISTON RING END GAP

a.
A400521C01
1.396,1.938 0.99,1.583 0.99,1.583 1.375,1.26 false 0.802,1.49 1.115,1.688 0.313,0.198 10 false *a 2.521,1.469 2.833,1.667 0.313,0.198 10 false *b
*a Piston Ring
*b 70 mm


Insert the piston ring into the cylinder bore.


b.

Using a piston, push in the piston ring a little beyond the bottom of the ring travel, 70 mm (2.76 in.) from the top of the cylinder block sub-assembly.


c.
A400522

Using a feeler gauge, measure the end gap.

Standard End Gap:
Item Specified Condition
No. 1 compression ring 0.160 to 0.185 mm (0.00630 to 0.00728 in.)
No. 2 compression ring 0.76 to 0.81 mm (0.0299 to 0.0319 in.)
Oil ring 0.100 to 0.350 mm (0.00394 to 0.01378 in.)


Maximum End Gap:
Item Specified Condition
No. 1 compression ring 0.185 mm (0.00728 in.)
No. 2 compression ring 0.81 mm (0.0319 in.)
Oil ring 0.35 mm (0.0138 in.)


HINT:

If the end gap is more than the maximum, replace the piston ring set. If the end gap is more than the maximum even with a new piston ring set, replace the cylinder block sub-assembly.



Hide 7.INSPECT PISTON PIN OIL CLEARANCE

HINT:

When replacing the piston and piston pin with supply parts, there are a number of piston diameter sizes to choose from, but there is only one size of piston pin diameter.


a.

Confirm each mark on the piston, piston pin and connecting rod.

A478734C02
0.938,2.052 1.083,2.052 1.083,2.052 1.208,1.594 true 2.792,2.156 2.604,2.156 2.604,2.156 2.51,1.667 true 4.802,2.438 4.323,2.438 true 2.833,2.063 3.146,2.26 0.313,0.198 10 false *a 0.75,1.969 1.063,2.167 0.313,0.198 10 false *b 4.135,2.344 4.448,2.542 0.313,0.198 10 false *c
*a Front Mark *b Piston Pin Hole Inside Diameter Mark
*c Connecting Rod Small End Bush Inside Diameter Mark - -



b.
A400524

Using a caliper gauge, measure the inside diameter of the piston pin hole.

Standard Piston Pin Hole Inside Diameter:

19.009 to 19.018 mm (0.748 to 0.749 in.)

Mark Specified Condition
A 24.001 to 24.004 mm (0.9449 to 0.9450 in.)
B 24.004 to 24.007 mm (0.9450 to 0.9452 in.)
C 24.007 to 24.010 mm (0.9452 to 0.9453 in.)


HINT:

If the diameter is not as specified, replace the piston and piston pin as a set.



c.
A400525C01
1.354,2.719 1.51,2.917 0.156,0.198 10 false a 1.552,4.281 1.708,4.479 0.156,0.198 10 false a 1.167,3.677 1.594,4.115 0.427,0.438 10 false b

Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:

19.004 to 19.013 mm (0.74819 to 0.74854 in.)

Mark Specified Condition
A 23.997 to 24.000 mm (0.9448 to 0.9449 in.)
B 24.000 to 24.003 mm (0.9449 to 0.9450 in.)
C 24.003 to 24.006 mm (0.9450 to 0.9451 in.)


HINT:

If the diameter is not as specified, replace the piston and piston pin as a set.


Measurement Position:
Measurement Position Piston Pin Position
a 5.0 mm (0.197 in.) from side edge
b 23.0 mm (0.906 in.) from side edge



d.
A400526

Using a caliper gauge, measure the inside diameter of the connecting rod small end bush.

Standard Connecting Rod Small End Bush Inside Diameter:

19.012 to 19.021 mm (0.74850 to 0.74886 in.)

Mark Specified Condition
A 24.005 to 24.008 mm (0.9451 to 0.9452 in.)
B 24.008 to 24.011 mm (0.9452 to 0.9453 in.)
C 24.011 to 24.014 mm (0.9453 to 0.9454 in.)


HINT:

If the inside diameter is not as specified, replace the connecting rod sub-assembly.



e.

Subtract the piston pin diameter measurement from the piston pin hole inside diameter measurement.

Standard Oil Clearance:

0.001 to 0.004 mm (0.0000394 to 0.0001575 in.)


Maximum Oil Clearance:

0.017 mm (0.000669 in.)


HINT:

If the oil clearance is more than the maximum, replace the piston and piston pin as a set.



f.

Subtract the piston pin diameter measurement from the connecting rod small end bush inside diameter measurement.

Standard Oil Clearance:

0.005 to 0.011 mm (0.000197 to 0.000433 in.)


Maximum Oil Clearance:

0.021 mm (0.000827 in.)


HINT:

If the oil clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the connecting rod sub-assembly and piston pin as a set.



Hide 13411 8.INSPECT CRANKSHAFT

a.

Inspect for runout.

i.

Clean the crank journal.


ii.

Place the crankshaft on V-blocks.


iii.
A478736

Using a dial indicator and V-blocks, measure the runout as shown in the illustration.

Maximum Runout:

0.03 mm (0.00118 in.)


HINT:

If the runout is more than the maximum, replace the crankshaft.




b.

Inspect the main journals.

i.

Using a micrometer, measure the diameter of each main journal.

Standard Main Journal Diameter:

55.988 to 56.000 mm (2.204 to 2.205 in.)


HINT:

If the diameter is not as specified, check the crankshaft oil clearance. If necessary, replace the crankshaft.



ii.
A478737

Check each main journal for taper and out-of-round as shown in the illustration.

Maximum Taper and Out-of-round:

0.003 mm (0.000118 in.)


HINT:

If the taper or out-of-round is more than the maximum, replace the crankshaft.




c.

Inspect the crank pins.

i.

Using a micrometer, measure the diameter of each crank pin.

Standard Crank Pin Diameter:

47.992 to 48.000 mm (1.88945 to 1.88976 in.)


HINT:

If the diameter is not as specified, check the connecting rod oil clearance. If necessary, replace the crankshaft.



ii.
A478738

Inspect each crank pin for taper and out-of-round as shown in the illustration.

Maximum Taper and Out-of-round:

0.003 mm (0.000118 in.)


HINT:

If the taper or out-of-round is more than the maximum, replace the crankshaft.




Hide 9.INSPECT CRANKSHAFT OIL CLEARANCE


b.

c.

Place the crankshaft on the cylinder block sub-assembly.


d.
A478739C01
1.521,1.01 0.75,0.698 true 0.563,0.604 0.875,0.76 0.313,0.156 10 false *a
*a Plastigage


Lay a strip of Plastigage across each journal.


e.

Install the crankshaft bearing caps.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE MECHANICAL)>CYLINDER BLOCK>REASSEMBLY

NOTICE:

Do not turn the crankshaft.




g.
A478740C01
1.49,1.01 0.833,0.688 true 0.635,0.573 0.948,0.729 0.313,0.156 10 false *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.026 to 0.049 mm (0.00102 to 0.00193 in.)


Maximum Oil Clearance:

0.049 mm (0.00193 in.)


NOTICE:

Remove the Plastigage completely after the measurement.


If the oil clearance is more than the maximum, replace the crankshaft bearing. If necessary, replace the crankshaft.

HINT:

If replacing a crankshaft bearing, select a new one with the same number. If the number of the crankshaft bearing cannot be determined, calculate the correct crankshaft bearing number by adding together the numbers imprinted on the cylinder block sub-assembly and crankshaft. Then refer to the following table for the appropriate crankshaft bearing number. There are 4 sizes of standard bearings, marked "1", "2", "3" or "4" accordingly.

A478741C01
1.615,0.896 1.854,0.49 true 1.042,2.896 1.354,3.375 1.354,3.375 1.021,3.156 true 5.094,0.896 4.802,0.385 false 5.25,3.156 5.25,2.958 false 4.896,3.333 4.896,2.948 false 4.698,2.667 4.917,2.26 false 5.073,2.667 5.167,2.469 false 2.708,2.521 2.708,2.354 true 2.531,2.063 2.531,1.896 true 2.344,2.521 2.344,2.354 true 2.167,2.063 2.167,1.896 true 4.667,0.229 4.979,0.385 0.313,0.156 10 false *a 1.896,0.385 2.208,0.542 0.313,0.156 10 false *b 1.302,3.406 1.615,3.563 0.313,0.156 10 false *c 2.021,1.719 2.417,1.917 0.396,0.198 10 false No. 1 2.188,2.531 2.583,2.729 0.396,0.198 10 false No. 2 2.385,1.719 2.781,1.917 0.396,0.198 10 false No. 3 2.563,2.542 2.958,2.74 0.396,0.198 10 false No. 4 4.75,3.354 5.146,3.552 0.396,0.198 10 false No. 2 5.219,2.385 5.615,2.583 0.396,0.198 10 false No. 3 4.969,2.177 5.365,2.375 0.396,0.198 10 false No. 1 5.115,3.208 5.51,3.406 0.396,0.198 10 false No. 4
*a Cylinder Block Number Mark (A) *b Crankshaft Number Mark (B)
*c Diameter Mark - -


EXAMPLE

Cylinder block sub-assembly (A) "3" + Crankshaft (B) "4" = Total "7"

Select the crankshaft bearing marked "3".

Crankshaft Bearing Chart:
(A) + (B) Use Crankshaft Bearing
0 to 2 1
3 to 5 2
6 to 8 3
9 to 11 4


Standard Cylinder Block Journal Inside Diameter (A):
Mark Specified Condition
0 60.000 to 60.003 mm (2.3622 to 2.3623 in.)
1 60.003 to 60.005 mm (2.3623 to 2.3624 in.)
2 60.005 to 60.007 mm (2.3624 to 2.3625 in.)
3 60.007 to 60.010 mm (2.3625 to 2.3626 in.)
4 60.010 to 60.012 mm (2.3626 to 2.3627 in.)
5 60.012 to 60.014 mm (2.3627 to 2.3628 in.)
6 60.014 to 60.016 mm (2.3628 to 2.3628 in.)


Standard Crankshaft Main Journal Diameter (B):
Mark Specified Condition
0 55.998 to 56.000 mm (2.20464 to 2.20472 in.)
1 55.996 to 55.998 mm (2.20456 to 2.20464 in.)
2 55.994 to 55.996 mm (2.20448 to 2.20456 in.)
3 55.992 to 55.994 mm (2.20441 to 2.20448 in.)
4 55.990 to 55.992 mm (2.20433 to 2.20441 in.)
5 55.988 to 55.990 mm (2.20425 to 2.20433 in.)


Standard Crankshaft Bearing Center Wall Thickness:
Mark Specified Condition
1 1.993 to 1.996 mm (0.07846 to 0.07858 in.)
2 1.996 to 1.999 mm (0.07858 to 0.07870 in.)
3 1.999 to 2.002 mm (0.07870 to 0.07882 in.)
4 2.002 to 2.005 mm (0.07882 to 0.07894 in.)





h.

Perform the inspection for each journal.


Hide 11416 10.INSPECT CRANKSHAFT BEARING CAP SET BOLT

a.
A478745C01
1.885,1.76 2.198,1.958 0.313,0.198 10 false *a 2.708,1.479 3.021,1.677 0.313,0.198 10 false *b 2.583,1.771 2.896,1.969 0.313,0.198 10 false *c
*a Measurement Area (B)
*b 5.0 mm (0.197 in.)
*c 10 mm (0.394 in.)
V100135

Measurement Location (A)


Using a vernier caliper, measure the outer diameter at position (A) shown in the illustration.

Standard Diameter:

10.73 to 10.97 mm (0.422 to 0.432 in.)



b.

Using a vernier caliper, measure the outer diameter within range (B) shown in the illustration at several locations.

HINT:
·

Perform the measurement within range (B) at several locations.

·

If the threads of the crankshaft bearing cap set bolt are damaged, replace the bolt with a new one.




c.

Calculate the difference between the measurement at position (A) and position (B).

Minimum Diameter:

The outer diameter difference is 0.3 mm (0.0118 in.)


HINT:
·

Outer Diameter Difference = Position (A) Outer Diameter - Position (B) Outer Diameter (Smallest Value)

·

If the outer diameter is below the minimum, the engine may be damaged.

Therefore, replace the crankshaft bearing cap set bolt with a new one.




Hide 13265 11.INSPECT CONNECTING ROD BOLT

a.
A478746C01
1.594,1.458 1.906,1.656 0.313,0.198 10 false *a 2.458,1.208 2.771,1.406 0.313,0.198 10 false *b 2.344,1.417 2.656,1.615 0.313,0.198 10 false *c
*a Measurement Area (B)
*b 5.0 mm (0.197 in.)
*c 10 mm (0.394 in.)
V100135

Measurement Location (A)


Using a vernier caliper, measure the outer diameter at position (A) shown in the illustration.

Standard Diameter:

8.36 to 8.5 mm (0.329 to 0.335 in.)



b.

Using a vernier caliper, measure the outer diameter within range (B) shown in the illustration at several locations.

HINT:
·

Perform the measurement within range (B) at several locations.

·

If the threads of the connecting rod bolt are damaged, replace the bolt with a new one.




c.

Calculate the difference between the measurement at position (A) and position (B).

Minimum Diameter:

The outer diameter difference is 0.05 mm (0.00197 in.)


HINT:
·

Outer Diameter Difference = Position (A) Outer Diameter - Position (B) Outer Diameter (Smallest Value)

·

If the outer diameter is below the minimum, the engine may be damaged.

Therefore, replace the connecting rod bolt with a new one.




Hide 12.INSPECT OIL NOZZLE SUB-ASSEMBLY

a.
A478742C01
1.51,0.521 2.104,0.521 false 1.333,0.448 1.646,0.604 0.313,0.156 10 false *a
*a Pin


Push the check valve with a pin to check that it is not stuck.

HINT:

If the check valve is stuck, replace the oil nozzle sub-assembly.



b.
A478743N02
1.969,1.156 2.385,0.74 true 1.448,0.292 1.604,0.49 0.156,0.198 10 false A 2.469,0.635 2.625,0.833 0.156,0.198 10 false B

Apply air into (A). Check that air does not leak through (B).

HINT:

If air leaks, clean or replace the oil nozzle sub-assembly.



c.
A478744C01
2.021,0.25 2.563,0.25 false 2.021,1.177 2.563,1.177 true 2.615,0.198 2.927,0.354 0.313,0.156 10 false *a 2.625,1.135 2.781,1.333 0.156,0.198 10 false B 1.49,0.292 1.646,0.49 0.156,0.198 10 false A
*a Pin


Push the check valve with a pin while applying air into (A). Check that air passes through (B).

HINT:

If air does not pass through (B), clean or replace the oil nozzle sub-assembly.