Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (for G16E-GTS) › from 2020.09
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0447912 FRONT SUSPENSION MEMBER(for G16E-GTS) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(for G16E-GTS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front suspension crossmember sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

a.
C440311

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 4.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 45260 5.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.REMOVE FRONT WHEELS

Hide 51410 7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

a.
C445903

Remove the 4 bolts, 4 screws, 12 clips and center engine under cover from the vehicle body.


Hide 51442C 8.REMOVE ENGINE UNDER COVER LH

a.
C445905

Remove the 2 clips and engine under cover LH from the vehicle body.


Hide 51441C 9.REMOVE ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 53876A 10.SEPARATE FRONT FENDER LINER LH

a.
C445906

Remove the 3 screws and separate the front fender liner LH.


Hide 53875A 11.SEPARATE FRONT FENDER LINER RH

HINT:

Perform the same procedure as for the LH side.


Hide 51447D 12.REMOVE CENTER NO. 4 ENGINE UNDER COVER

a.
C445904

Remove the 4 bolts and center No. 4 engine under cover from the vehicle body.


Hide 48810 13.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

a.
C445907

Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 14.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 15.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.
C447095C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw to remove the steering knuckle seal as shown in the illustration.


b.
C445920

Remove the cotter pin and nut.


c.
C445909N01
2.635,1.698 2.906,1.385 false 2.333,1.625 2.792,1.823 0.458,0.198 10 false SST

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the lower ends of the tie rod end sub-assembly LH and SST are aligned.



d.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.



e.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle LH.

SST
09960-20010  (09961-02010)

C445910C01
1.208,2.771 1.375,2.604 false 0.479,1.083 0.729,1.083 true 3.563,2.677 3.563,2.427 false 0.281,1 0.448,1.167 0.167,0.167 10 true *a 6.635,0.844 6.948,1 0.313,0.156 10 false *c 2.667,1.083 2.979,1.24 0.313,0.156 10 false *d 0.396,2.844 0.802,3.177 0.406,0.333 10 false A 0.385,3.063 0.792,3.396 0.406,0.333 10 false B 5.667,2.521 5.979,2.677 0.313,0.156 10 false *b 5.594,2.792 5.906,2.948 0.313,0.156 10 false *b 1.427,2.51 1.74,2.667 0.313,0.156 10 false *d 3.469,2.719 3.865,2.885 0.396,0.167 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45046 16.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 17.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 18.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 19.REMOVE EXHAUST SENSOR CLAMP BRACKET

a.
C445912

Remove the bolt, 2 clamps and separate the exhaust sensor clamp bracket from the front suspension crossmember sub-assembly.


Hide 20.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
C445915

Remove the 2 bolts and front suspension member reinforcement LH from the front suspension crossmember sub-assembly and vehicle body.


Hide 21.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 22.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C445911

Remove the bolt and separate the wiring harness clamp bracket from the front suspension crossmember sub-assembly.


b.
C445913C01
0.615,2.313 0.781,2.313 0.781,2.313 1.115,1.729 true 0.865,0.948 0.99,0.948 0.99,0.948 1.396,1.302 true 0.573,0.844 0.813,1.01 0.24,0.167 10 true *b 0.406,2.219 0.719,2.375 0.313,0.156 10 false *a
*a Transmission Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden block placement location


Using a transmission jack and a wooden block, support the engine assembly with transaxle.

CAUTION:
C427884

·

Support the engine assembly with transaxle until the front suspension crossmember sub-assembly is installed.

·

If the support is removed before the front suspension crossmember sub-assembly is installed, the engine assembly with transaxle may drop.




c.
C445914

Remove the bolt and separate the engine moving control rod.


d.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

C445916C01
2.99,1.5 3.396,1.646 3.396,1.646 3.563,1.646 true 0.906,1.667 2.906,1.667 2.906,1.667 2.906,1.167 true 2.729,1.646 2.729,1.115 true 1.75,1.667 1.75,1.25 true 1.333,1.667 1.333,1.333 true 3.583,1.542 3.896,1.698 0.313,0.156 10 false *a 0.677,1.573 0.875,1.75 0.198,0.177 10 true *b
*a Engine Lifter *b Attachment
V100155

Attachment placement location - -


CAUTION:
·
C320210

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front suspension crossmember sub-assembly level.



e.
C445917

Remove the 2 bolts.


f.
C449745

Remove the 4 bolts and front suspension crossmember sub-assembly.


g.

Slowly lower the front suspension crossmember sub-assembly.

NOTICE:
·

When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

·

Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.




Hide 12363A 23.REMOVE ENGINE MOVING CONTROL ROD

a.
C445918

Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.


Hide 48069 24.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C445919

Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

NOTICE:

Loosen the bolt with the nut secured.



Hide 48068 25.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 26.REMOVE STEERING LINK ASSEMBLY

Hide 48811 27.REMOVE FRONT STABILIZER BAR