Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER (for G16E-GTS) › from 2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0447922 REAR SHOCK ABSORBER(for G16E-GTS) A

REAR SUSPENSION  REAR SHOCK ABSORBER(for G16E-GTS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 48540 2.LOOSEN REAR SHOCK ABSORBER ASSEMBLY

a.
C445817C01
1,0.656 1.167,0.656 1.167,0.656 1.594,0.979 true 0.781,0.583 0.99,0.802 0.208,0.219 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



Hide 48840A 3.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48540 4.SEPARATE REAR SHOCK ABSORBER ASSEMBLY

a.
C445818C01
1.917,1.417 2.167,1.417 true 2.167,1.917 2.417,1.917 true 2.188,1.333 2.5,1.49 0.313,0.156 10 true *a 2.438,1.833 2.75,1.99 0.313,0.156 10 true *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.
C445819

Remove the 2 bolts and separate the rear shock absorber assembly from the vehicle.


Hide 48790 5.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY

a.
C445820

Remove the bolt and nut, and separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Loosen the bolt with the nut secured.



Hide 48540 6.REMOVE REAR SHOCK ABSORBER ASSEMBLY

a.
C445817C02
1,0.667 1.167,0.667 1.167,0.667 1.594,0.948 true 0.74,0.552 0.948,0.75 0.208,0.198 10 true *1
*1 Rear Axle Carrier Pin


Remove the nut, plate washer and rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



Hide 48554A 7.REMOVE REAR SHOCK ABSORBER CAP

a.
C445821C01
0.979,0.479 1.51,0.906 true 0.76,0.354 1.073,0.51 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear shock absorber cap from the rear shock absorber assembly.


Hide 48760B 8.REMOVE REAR SUSPENSION SUPPORT ASSEMBLY

a.
C450298C01
2.333,1.25 1.365,1.25 true 1.042,1.177 1.5,1.375 0.458,0.198 10 false SST 1.76,2.854 2.073,3.01 0.313,0.156 10 false *a 3.135,1.604 3.344,1.854 0.208,0.25 10 false *b
*a Turn
*b Hold


Secure the rear shock absorber assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and remove the rear support to rear shock absorber nut.

SST
09729-00170  


c.

Remove the rear suspension support assembly from the rear shock absorber assembly.