Home › Suspension › REAR SUSPENSION › REAR COIL SPRING (for TMC Made except G16E-GTS) › from 2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0447939 REAR COIL SPRING(for TMC Made except G16E-GTS) A

REAR SUSPENSION  REAR COIL SPRING(for TMC Made except G16E-GTS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48259A 1.INSTALL REAR UPPER COIL SPRING INSULATOR

a.
C427936C01
1.917,0.302 2.229,0.458 0.313,0.156 10 false *a
*a Fit


Install the rear upper coil spring insulator to the rear coil spring.

NOTICE:
·

Install the rear upper coil spring insulator so that the dimension between the stopper and upper end of the rear coil spring is 10 mm (0.394 in.) or less.

·

The identification mark of the rear coil spring should be towards the underside.




Hide 48258C 2.INSTALL REAR LOWER COIL SPRING INSULATOR

a.
C428584C01
1.583,1.25 1.823,1.438 0.24,0.188 10 true *a
*a Fit


Install the rear lower coil spring insulator to the rear axle beam assembly.

NOTICE:

Securely insert the protrusion of the rear lower coil spring insulator into the guide holes of the rear axle beam assembly.



Hide 48231B 3.INSTALL REAR COIL SPRING

a.

Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.


b.

Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Loosen the bolts with the nuts secured.



c.

Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.


d.
C433946C01
0,0 0,0 false
V100145

Identification Mark


Set the rear coil spring to the rear axle beam assembly.

NOTICE:
·

Make sure that there is no gap between the coil end of the rear coil spring and the stopper of the rear lower coil spring insulator.

·

Set the rear coil spring so that the identification mark is positioned as shown in the illustration.




e.

Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks and temporarily install the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.

C433945C01
4.906,2.281 5.24,2.281 true 4.792,1.865 5.125,1.865 true 2.042,1.885 2.375,1.885 true 2.021,2.344 2.354,2.344 true 2.396,1.781 2.615,1.948 0.219,0.167 10 true *a 4.656,2.188 4.885,2.354 0.229,0.167 10 true *b 4.542,1.771 4.76,1.938 0.219,0.167 10 true *a 2.385,2.25 2.604,2.417 0.219,0.167 10 true *b
*a Wooden Block *b Jack


NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.


HINT:

Insert the bolt with the threaded end facing the outside of the vehicle.



Hide 46430 4.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 46420 5.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Perform the same procedure as for the No. 3 side.


Hide 47319F 6.INSTALL REAR FLEXIBLE HOSE LH

a.
C436102C01
1.531,2.26 1.76,2.438 0.229,0.177 10 false *a
*a Torque Wrench Fulcrum Length


Install the rear flexible hose LH to the rear axle beam assembly with a new clip.

NOTICE:

Install the clip as far as it will go.



b.

Using a union nut wrench 10 mm, connect the brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 47318F 7.INSTALL REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89516D 8.INSTALL SKID CONTROL SENSOR WIRE LH

a.

Install the skid control sensor wire LH to the rear axle beam assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the skid control sensor wire when installing it.



b.

Connect the skid control sensor wire LH connector.


Hide 89516C 9.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 11.INSTALL REAR WHEEL

Hide 42110F 13.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

Hide 48540 14.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48760B 15.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 16.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Hide 19. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 20.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)