Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › 2020.07–2021.11
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0417607 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  INSTALLATION  


PROCEDURE

Hide 42110F 1.TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.

Slowly jack up the rear axle beam assembly using an engine lifter, 2 wooden blocks and 2 plate lift attachments or equivalent tools and temporarily install the rear axle beam assembly to the vehicle with the 2 bolts.

C437645C04
6.344,1.719 5.813,1.625 true 1.281,1.667 0.719,1.792 true 2.99,1.573 3.625,1.271 3.625,1.271 4.135,1.573 true 2.958,3.125 3.625,2.198 true 0.448,1.698 0.688,1.927 0.24,0.229 10 true *b 3.521,1.073 3.771,1.25 0.25,0.177 10 true *a 2.781,3.063 3.094,3.219 0.313,0.156 10 false *c 6.375,1.635 6.594,1.854 0.219,0.219 10 true *b
*a Plate Lift Attachment *b Wooden Block
*c Engine Lifter - -


CAUTION:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Temporarily install the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.

NOTICE:

Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.



Hide 48231B 2.INSTALL REAR COIL SPRING LH (for TMC Made)

Hide 48231A 3.INSTALL REAR COIL SPRING RH (for TMC Made)

HINT:

Perform the same procedure as for the LH side.


Hide 48231B 4.INSTALL REAR COIL SPRING LH (for TMMF Made)

Hide 48231A 5.INSTALL REAR COIL SPRING RH (for TMMF Made)

HINT:

Perform the same procedure as for the LH side.


Hide 42450B 6.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for TMC Made)

Hide 42450A 7.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for TMC Made)

HINT:

Perform the same procedure as for the LH side.


Hide 42450B 8.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for TMMF Made)

Hide 42450A 9.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for TMMF Made)

HINT:

Perform the same procedure as for the LH side.


Hide 10.INSTALL REAR WHEEL

Hide 11. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 42110F 12.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.

Fully tighten the 2 bolts.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 48540 13.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48760B 14.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 15.BLEED BRAKE LINE (for Rear Drum Brake)

Hide 18. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (for HV Model TMC Made)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 19.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)