The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the rear wheel alignment procedure are shown below.
| Replacement Part or Procedure | Necessary Procedure | Effect/Inoperative when not Performed | Link |
|---|---|---|---|
| Rear wheel alignment adjustment | for HV Model:
1.
Perform "Reset Memory" 2.
Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) |
·
DTCs are stored ·
ABS warning light illuminates ·
Brake system warning light (yellow indicator) illuminates ·
Slip indicator light illuminates ·
VSC disabled or malfunctions |
|
| for Gasoline Model:
Calibration |
·
DTCs are stored ·
ABS warning light illuminates ·
Slip indicator light illuminates ·
VSC disabled or malfunctions |
|
1.INSPECT TIRES
2.MEASURE VEHICLE HEIGHT
3.INSPECT CAMBER
Inspect while the vehicle is unloaded.
| *a | Camber-caster-kingpin Gauge |
Install a camber-caster-kingpin gauge.
Inspect the camber.
| Engine | Transaxle | Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|---|---|
| M15A-FKS | M/T | 175/70R14
185/60R15 185/55R16 |
-1°03' +/- 0°30' (-1.05° +/- 0.50°) | 0°33' (0.55°) or less |
| CVT | 175/70R14
185/60R15 185/55R16 |
-1°03' +/- 0°30' (-1.05° +/- 0.50°) | ||
| M15A-FXE | - | 175/70R14
185/60R15 185/55R16 |
-1°03' +/- 0°30' (-1.05° +/- 0.50°) |
| Engine | Transaxle | Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|---|---|
| 1KR-FE | M/T | 185/65R15
195/55R16 |
-0°57' +/- 0°30' (-0.95° +/- 0.50°) | 0°33' (0.55°) or less |
| M15A-FKS | M/T | 185/65R15
195/55R16 205/45R17 |
-0°57' +/- 0°30' (-0.95° +/- 0.50°) | |
| CVT | 185/65R15
195/55R16 205/45R17 |
-0°57' +/- 0°30' (-0.95° +/- 0.50°) | ||
| M15A-FXE | - | 185/65R15 | -0°57' +/- 0°30' (-0.95° +/- 0.50°) | |
| 195/55R16
205/45R17 |
-0°58' +/- 0°30' (-0.97° +/- 0.50°) |
| Engine | Transaxle | Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|---|---|
| 1KR-FE | M/T | 185/65R15 | -0°53' +/- 0°30' (-0.88° +/- 0.50°) | 0°33' (0.55°) or less |
| M15A-FKS | M/T | 185/65R15 | -0°53' +/- 0°30' (-0.88° +/- 0.50°) | |
| CVT | 185/65R15 | -0°53' +/- 0°30' (-0.88° +/- 0.50°) | ||
| M15A-FXE | - | 185/65R15 | -0°54' +/- 0°30' (-0.90° +/- 0.50°) |
| Engine | Transaxle | Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|---|---|
| 1KR-FE | M/T | 185/65R15 | -0°57' +/- 0°30' (-0.95° +/- 0.50°) | 0°33' (0.55°) or less |
| M15A-FKS | M/T | 185/65R15 | -0°57' +/- 0°30' (-0.95° +/- 0.50°) | |
| CVT | 185/65R15 | -0°57' +/- 0°30' (-0.95° +/- 0.50°) | ||
| M15A-FXE | - | 185/65R15 | -0°57' +/- 0°30' (-0.95° +/- 0.50°) |
Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.
4.INSPECT TOE-IN
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N (for CVT, Hybrid Transaxle).
Release the parking brake and move the shift lever to neutral (for Manual Transaxle).
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
| Engine | Transaxle | Tire Size | Specified Condition |
|---|---|---|---|
| M15A-FKS | M/T | 175/70R14
185/60R15 |
C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°) |
| B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.) | |||
| 185/55R16 | C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°) | ||
| B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.) | |||
| CVT | 175/70R14
185/60R15 |
C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°) | |
| B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.) | |||
| 185/55R16 | C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°) | ||
| B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.) | |||
| M15A-FXE | - | 175/70R14
185/60R15 |
C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°) |
| B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.) | |||
| 185/55R16 | C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°) | ||
| B - A: 4.4 +/- 3.0 mm (0.173 +/- 0.118 in.) |
| Engine | Transaxle | Tire Size | Specified Condition |
|---|---|---|---|
| 1KR-FE | M/T | 185/65R15
195/55R16 |
C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°) |
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) | |||
| M15A-FKS | M/T | 185/65R15
195/55R16 205/45R17 |
C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°) |
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) | |||
| CVT | 185/65R15
195/55R16 205/45R17 |
C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°) | |
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) | |||
| M15A-FXE | - | 185/65R15
195/55R16 |
C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°) |
| B - A: 4.6 +/- 3.1 mm (0.187 +/- 0.122 in.) | |||
| 205/45R17 | C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°) | ||
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) |
| Engine | Transaxle | Tire Size | Specified Condition |
|---|---|---|---|
| 1KR-FE | M/T | 185/65R15 | C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°) |
| B - A: 3.9 +/- 3.1 mm (0.154 +/- 0.122 in.) | |||
| M15A-FKS | M/T | 185/65R15 | C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°) |
| B - A: 3.9 +/- 3.1 mm (0.154 +/- 0.122 in.) | |||
| CVT | 185/65R15 | C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°) | |
| B - A: 3.9 +/- 3.1 mm (0.154 +/- 0.122 in.) | |||
| M15A-FXE | - | 185/65R15 | C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°) |
| B - A: 4.0 +/- 3.1 mm (0.157 +/- 0.122 in.) |
| Engine | Transaxle | Tire Size | Specified Condition |
|---|---|---|---|
| 1KR-FE | M/T | 185/65R15 | C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°) |
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) | |||
| M15A-FKS | M/T | 185/65R15 | C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°) |
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) | |||
| CVT | 185/65R15 | C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°) | |
| B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.) | |||
| M15A-FXE | - | 185/65R15 | C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°) |
| B - A: 4.6 +/- 3.1 mm (0.187 +/- 0.122 in.) |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.
5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
6.INSPECT AND ADJUST HEADLIGHT AIMING
These procedures are to be performed when suspension or tires components have been removed or replaced.
for Halogen Headlight
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>ADJUSTMENT
for LED Headlight
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>ADJUSTMENT
7.PERFORM CALIBRATION
for HV Model TMC Made
for HV Model TMMF Made
for Gasoline Model TMC Made
for Gasoline Model TMMF Made