Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2020.09–2021.11
RM36W0E _58 Vehicle Interior _087985 METER / GAUGE / DISPLAY _0420292 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150819  Turn Signal/Hazard Flasher Circuit Current Above Threshold  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.

HINT:

If there is a short in a turn signal light circuit, all of the turn signal lights in that circuit will not blink.


DTC No. Detection Item DTC Detection Condition Trouble Area
B150819 Turn Signal/Hazard Flasher Circuit Current Above Threshold Diagnosis Condition:

Auxiliary battery voltage is 10 V or more


Malfunction Status:

Short in turn signal light circuit


·

Headlight assembly

-

Front turn signal light socket*1

-

Front turn signal light bulb*1

-

Headlight unit assembly LH*2

-

Headlight unit assembly RH*2

-

Wire Harness LH*2

-

Wire Harness RH*2


·

Outer rear view mirror assembly

-

Side turn signal light assembly LH

-

Side turn signal light assembly RH


·

Rear combination light assembly

-

Rear turn signal light socket*3

-

Rear turn signal light bulb*3

-

Rear turn signal light LED*4


·

Harness or connector

·

Combination meter assembly



*1: for Halogen Headlight

*2: for LED Headlight

*3: for Rear Turn Signal Light Bulb Type

*4: for Rear Turn Signal Light LED Type


WIRING DIAGRAM

E455953E01
0.177,0.177 1.49,0.688 1.313,0.51 12 false for LH Side: 2.958,1.208 3.115,1.406 0.156,0.198 10 false B 2.958,1.51 3.115,1.708 0.156,0.198 10 false E 5.021,1.198 5.177,1.396 0.156,0.198 10 false 1 5.219,1.188 5.552,1.427 0.333,0.24 10 false LL 2.948,3.031 3.104,3.229 0.156,0.198 10 false B 2.948,3.333 3.104,3.531 0.156,0.198 10 false E 3.958,1.198 4.26,1.406 0.302,0.208 10 false *1 3.958,3.042 4.229,3.24 0.271,0.198 10 false *2 0.417,7.5 2.5,7.833 2.083,0.333 10 false *1: for Halogen Headlight 5.938,0.813 6.438,1.063 0.5,0.25 10 false TURN L 6.021,2.49 6.708,2.99 0.688,0.5 10 false FLASHER IC 5.083,7.229 5.417,7.51 0.333,0.281 10 false H7 5.073,7.375 6.979,7.896 1.906,0.521 10 false Combination Meter Assembly 1.01,1.833 3.115,2.167 2.104,0.333 10 false Front Turn Signal Light Socket 0.51,3.667 1.458,4.125 0.948,0.458 10 false Headlight Unit Assembly LH 0.938,2.25 1.333,2.479 0.396,0.229 10 false A16 0.948,2.396 2.677,2.75 1.729,0.354 10 false Headlight Assembly LH*1 3.146,1.208 3.302,1.406 0.156,0.198 10 false 1 3.156,3.344 3.313,3.542 0.156,0.198 10 false 5 3.156,1.51 3.313,1.708 0.156,0.198 10 false 2 3.146,3.042 3.302,3.24 0.156,0.198 10 false 6 0.917,4.563 2.646,4.917 1.729,0.354 10 false Headlight Assembly LH*2 0.927,4.427 1.25,4.656 0.323,0.229 10 false A4 2.104,5.292 2.281,5.521 0.177,0.229 10 false B 2.094,5.875 2.25,6.073 0.156,0.198 10 false - 0.417,8.5 3.25,8.833 2.833,0.333 10 false *4: for TMC Made 5 Door with Mirror Heater 0.229,7 2.802,7.573 2.573,0.573 10 false Outer Rear View Mirror Assembly LH 0.688,6.229 2.167,6.896 1.479,0.667 10 false Side Turn Signal Light Assembly LH 3.938,5.969 4.396,6.167 0.458,0.198 10 false L10 3.938,5.396 4.396,5.594 0.458,0.198 10 false L10 3.573,5.396 3.885,5.594 0.313,0.198 10 false L8 3.573,5.979 3.885,6.177 0.313,0.198 10 false L8 0.417,7.833 2.167,8.167 1.75,0.333 10 false *2: for LED Headlight 0.417,8.167 3.417,8.5 3,0.333 10 false *3: for TMC Made 5 Door without Mirror Heater 3.573,5.594 3.885,5.792 0.313,0.198 10 false *4 3.573,6.188 3.885,6.385 0.313,0.198 10 false *4 4,6.177 4.313,6.375 0.313,0.198 10 false *3 3.99,5.594 4.302,5.792 0.313,0.198 10 false *3 3.552,5.198 3.865,5.396 0.313,0.198 10 false 16 3.563,5.781 3.875,5.979 0.313,0.198 10 false 15 4.01,5.771 4.167,5.969 0.156,0.198 10 false 5 4.01,5.198 4.167,5.396 0.156,0.198 10 false 4 1.854,3.688 3.073,4.167 1.219,0.479 10 false Wire Harness LH 3.177,6.188 3.49,6.385 0.313,0.198 10 false *5 2.771,5.594 3.083,5.792 0.313,0.198 10 false *6 2.781,6.188 3.094,6.385 0.313,0.198 10 false *6 3.177,5.594 3.49,5.792 0.313,0.198 10 false *5 3.146,5.385 3.604,5.583 0.458,0.198 10 false L10 3.135,5.979 3.594,6.177 0.458,0.198 10 false L10 2.729,5.396 3.188,5.594 0.458,0.198 10 false L14 2.729,5.969 3.188,6.167 0.458,0.198 10 false L14 3.208,5.198 3.365,5.396 0.156,0.198 10 false 5 2.76,5.198 3.073,5.396 0.313,0.198 10 false 10 3.208,5.781 3.365,5.979 0.156,0.198 10 false 4 2.771,5.781 3.083,5.979 0.313,0.198 10 false 11 3.667,7.833 6.917,8.167 3.25,0.333 10 false *5: for TMMF Made 5 Door without Auto Retractor 3.677,8.167 6.75,8.5 3.073,0.333 10 false *6: for TMMF Made 5 Door with Auto Retractor 3.667,8.5 6.323,8.833 2.656,0.333 10 false *7: for 3 Door 2.354,5.969 2.813,6.167 0.458,0.198 10 false L14 2.344,5.396 2.802,5.594 0.458,0.198 10 false L14 2.406,5.198 2.563,5.396 0.156,0.198 10 false 1 2.417,5.781 2.573,5.979 0.156,0.198 10 false 2 2.385,5.594 2.698,5.792 0.313,0.198 10 false *7 2.385,6.188 2.698,6.385 0.313,0.198 10 false *7

E436697E15
5.177,3.552 5.49,3.75 0.313,0.198 10 false H7 5.177,3.719 7.073,4.198 1.896,0.479 10 false Combination Meter Assembly 5.99,1.24 6.688,1.615 0.698,0.375 10 false FLASHER IC 5.198,0.844 5.813,1.042 0.615,0.198 10 false TRNL 5.01,0.844 5.167,1.042 0.156,0.198 10 false 5 3.948,0.865 4.26,1.063 0.313,0.198 10 false *1 4.51,1.375 4.823,1.573 0.313,0.198 10 false *2 1.167,1.5 3.198,1.917 2.031,0.417 10 false Rear Combination Light Socket 0.729,2.354 3.323,2.76 2.594,0.406 10 false Rear Combination Light Assembly LH*1 0.729,4.396 3.323,4.802 2.594,0.406 10 false Rear Combination Light Assembly LH*2 1.104,3.823 3.01,4.135 1.906,0.313 10 false Rear Turn Signal Light LED 3.115,3.177 3.271,3.375 0.156,0.198 10 false B 3.115,3.469 3.271,3.667 0.156,0.198 10 false E 3.104,0.865 3.26,1.063 0.156,0.198 10 false B 3.115,1.156 3.271,1.354 0.156,0.198 10 false E 3.292,0.875 3.469,1.156 0.177,0.281 10 false 1 3.302,3.479 3.479,3.76 0.177,0.281 10 false 1 3.302,1.156 3.458,1.354 0.156,0.198 10 false 2 3.302,3.188 3.458,3.385 0.156,0.198 10 false 2 0.729,4.24 2,4.552 1.271,0.313 10 false T3*3, O105*4 0.719,2.198 1.938,2.531 1.219,0.333 10 false T1*3, O101*4 0.198,5.167 3.26,5.365 3.063,0.198 10 false *1: for Rear Turn Signal Light Bulb Type 0.198,5.469 3.26,5.667 3.063,0.198 10 false *2: for Rear Turn Signal Light LED Type 0.198,0.156 1.469,0.448 1.271,0.292 12 false for LH Side: 3.094,5.156 5.406,5.406 2.313,0.25 10 false *3: for TMC Made 5 Door 3.094,5.5 5.667,5.75 2.573,0.25 10 false *4: for 3 Door or TMMF Made 5 Door

E455953E02
0.177,0.177 1.646,0.646 1.469,0.469 12 false for RH Side: 2.958,1.198 3.115,1.396 0.156,0.198 10 false B 2.948,1.51 3.104,1.708 0.156,0.198 10 false E 5.021,1.188 5.177,1.385 0.156,0.198 10 false 2 5.219,1.188 5.552,1.427 0.333,0.24 10 false LR 2.958,3.042 3.115,3.24 0.156,0.198 10 false B 2.969,3.344 3.125,3.542 0.156,0.198 10 false E 3.958,1.198 4.26,1.406 0.302,0.208 10 false *1 3.958,3.042 4.229,3.24 0.271,0.198 10 false *2 0.333,7.5 2,7.833 1.667,0.333 10 false *1: for Halogen Headlight 5.938,0.813 6.521,1.125 0.583,0.313 10 false TURN R 6.042,2.5 6.719,2.99 0.677,0.49 10 false FLASHER IC 5.125,7.229 5.458,7.51 0.333,0.281 10 false H7 5.115,7.385 7.01,7.906 1.896,0.521 10 false Combination Meter Assembly 1.135,1.833 3.24,2.167 2.104,0.333 10 false Front Turn Signal Light Socket 0.583,3.667 1.552,4.208 0.969,0.542 10 false Headlight Unit Assembly RH 0.938,2.25 1.333,2.479 0.396,0.229 10 false A17 0.948,2.396 2.677,2.75 1.729,0.354 10 false Headlight Assembly RH*1 3.146,1.208 3.302,1.406 0.156,0.198 10 false 1 3.146,3.344 3.302,3.542 0.156,0.198 10 false 5 3.156,1.51 3.313,1.708 0.156,0.198 10 false 2 3.135,3.042 3.292,3.24 0.156,0.198 10 false 6 0.917,4.573 2.802,4.896 1.885,0.323 10 false Headlight Assembly RH*2 0.927,4.406 1.25,4.635 0.323,0.229 10 false A5 2.094,5.281 2.271,5.51 0.177,0.229 10 false B 2.094,5.875 2.25,6.073 0.156,0.198 10 false - 0.333,8.5 3.167,8.833 2.833,0.333 10 false *4: for TMC Made 5 Door with Mirror Heater 0.229,7 2.719,7.438 2.49,0.438 10 false Outer Rear View Mirror Assembly RH 0.625,6.219 2.104,6.667 1.479,0.448 10 false Side Turn Signal Light Assembly RH 3.948,5.969 4.406,6.167 0.458,0.198 10 false K10 3.938,5.396 4.396,5.594 0.458,0.198 10 false K10 3.573,5.396 3.885,5.594 0.313,0.198 10 false K8 3.563,5.969 3.875,6.167 0.313,0.198 10 false K8 0.333,7.833 2,8.167 1.667,0.333 10 false *2: for LED Headlight 0.333,8.167 3.417,8.5 3.083,0.333 10 false *3: for TMC Made 5 Door without Mirror Heater 3.583,5.594 3.896,5.792 0.313,0.198 10 false *4 3.573,6.177 3.885,6.375 0.313,0.198 10 false *4 4,6.177 4.313,6.375 0.313,0.198 10 false *3 3.979,5.594 4.292,5.792 0.313,0.198 10 false *3 3.563,5.198 3.875,5.396 0.313,0.198 10 false 16 3.563,5.781 3.875,5.979 0.313,0.198 10 false 15 4.01,5.781 4.167,5.979 0.156,0.198 10 false 5 4,5.188 4.156,5.385 0.156,0.198 10 false 4 1.865,3.677 3.135,4.177 1.271,0.5 10 false Wire Harness RH 3.177,5.594 3.49,5.792 0.313,0.198 10 false *5 2.771,5.594 3.083,5.792 0.313,0.198 10 false *6 3.135,5.385 3.594,5.583 0.458,0.198 10 false K10 2.729,5.385 3.188,5.583 0.458,0.198 10 false K14 3.125,5.969 3.583,6.167 0.458,0.198 10 false K10 3.177,6.177 3.49,6.375 0.313,0.198 10 false *5 2.729,5.969 3.188,6.167 0.458,0.198 10 false K14 2.771,6.177 3.083,6.375 0.313,0.198 10 false *6 3.219,5.188 3.375,5.385 0.156,0.198 10 false 5 2.76,5.198 3.073,5.396 0.313,0.198 10 false 10 3.208,5.781 3.365,5.979 0.156,0.198 10 false 4 2.771,5.771 3.083,5.969 0.313,0.198 10 false 11 3.75,7.833 7,8.167 3.25,0.333 10 false *5: for TMMF Made 5 Door without Auto Retractor 3.75,8.167 6.833,8.5 3.083,0.333 10 false *6: for TMMF Made 5 Door with Auto Retractor 3.75,8.5 6.417,8.833 2.667,0.333 10 false *7: for 3 Door 2.375,6.177 2.688,6.375 0.313,0.198 10 false *7 2.333,5.969 2.792,6.167 0.458,0.198 10 false K14 2.323,5.385 2.781,5.583 0.458,0.198 10 false K14 2.385,5.594 2.698,5.792 0.313,0.198 10 false *7 2.406,5.188 2.719,5.385 0.313,0.198 10 false 1 2.427,5.781 2.74,5.979 0.313,0.198 10 false 2

E436697E16
5.156,3.521 5.469,3.719 0.313,0.198 10 false H7 5.146,3.688 7.042,4.177 1.896,0.49 10 false Combination Meter Assembly 6.031,1.521 6.719,1.906 0.688,0.385 10 false FLASHER IC 5.198,0.844 5.813,1.042 0.615,0.198 10 false TRNR 5.01,0.844 5.167,1.042 0.156,0.198 10 false 6 3.948,0.865 4.26,1.063 0.313,0.198 10 false *1 4.51,1.375 4.823,1.573 0.313,0.198 10 false *2 1.198,1.5 3.156,2.031 1.958,0.531 10 false Rear Combination Light Socket 0.729,2.354 3.458,2.792 2.729,0.438 10 false Rear Combination Light Assembly RH*1 0.729,4.396 3.344,4.813 2.615,0.417 10 false Rear Combination Light Assembly RH*2 1.156,3.813 2.958,4.104 1.802,0.292 10 false Rear Turn Signal Light LED 3.115,3.177 3.271,3.375 0.156,0.198 10 false B 3.115,3.469 3.271,3.667 0.156,0.198 10 false E 3.104,0.865 3.26,1.063 0.156,0.198 10 false B 3.115,1.156 3.271,1.354 0.156,0.198 10 false E 3.292,0.875 3.469,1.156 0.177,0.281 10 false 1 3.302,3.479 3.479,3.76 0.177,0.281 10 false 1 3.302,1.156 3.458,1.354 0.156,0.198 10 false 2 3.302,3.188 3.458,3.385 0.156,0.198 10 false 2 0.729,4.24 2.01,4.625 1.281,0.385 10 false S3*3, O106*4 0.719,2.198 1.938,2.5 1.219,0.302 10 false S1*3, O102*4 0.188,5.083 3.25,5.281 3.063,0.198 10 false *1: for Rear Turn Signal Light Bulb Type 0.188,5.417 3.25,5.615 3.063,0.198 10 false *2: for Rear Turn Signal Light LED Type 0.198,0.167 1.646,0.521 1.448,0.354 12 false for RH Side: 3,5.083 6.063,5.281 3.063,0.198 10 false *3: for TMC Made 5 Door 3,5.417 6.083,5.625 3.083,0.208 10 false *4: for 3 Door or TMMF Made 5 Door

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the turn signal light bulbs before performing the following procedure.



PROCEDURE

1.CHECK SYMPTOMS
a.

Check the problem symptoms.


Result:
Result Proceed to
All LH side turn signal lights do not blink A
All RH side turn signal lights do not blink B



A

2.CHECK VEHICLE TYPE

B

30.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Halogen Headlight A
for LED Headlight B




A

3.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

B

19.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)
3.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


Procedure1

b.

Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.

HINT:

If the LH side turn signal lights other than the front turn signal light blink, the headlight assembly LH is malfunctioning.



Post-procedure1

c.

None


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



A

B

4.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
4.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the headlight assembly LH connector.


b.

Disconnect the L10*1, L8*2 or L14*3 outer rear view mirror assembly LH connector.

*1: for TMC Made 5 Door without Mirror Heater or TMMF Made 5 Door without Auto Retractor

*2: for TMC Made 5 Door with Mirror Heater

*3: for TMMF Made 5 Door with Auto Retractor



Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



A

5.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

B

6.CHECK VEHICLE TYPE
5.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.

for TMC Made 5 Door: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMC Made)>REMOVAL

for TMMF Made 5 Door: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMMF Made)>REMOVAL


b.

Connect the outer rear view mirror assembly LH connector.


Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



A

B

6.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Rear Turn Signal Light Bulb Type A
for Rear Turn Signal Light LED Type B




A

7.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

B

13.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
7.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly LH connector.


b.

Disconnect the T1*1 or O101*2 rear combination light assembly LH connector.

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door



Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.

HINT:

If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the rear turn signal light blink A
All LH side turn signal lights do not blink B



A

B

8.CHECK VEHICLE TYPE
8.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for TMC Made 5 Door without Mirror Heater A
for TMC Made 5 Door with Mirror Heater B
for TMMF Made 5 Door without Auto Retractor C
for TMMF Made 5 Door with Auto Retractor D




A

9.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

11.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

D

12.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L10-4 (B) - Body ground Always 10 kΩ or higher
T1-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L8-16 (B) - Body ground Always 10 kΩ or higher
T1-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L10-5 (B) - Body ground Always 10 kΩ or higher
O101-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L14 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L14-10 (B) - Body ground Always 10 kΩ or higher
O101-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly LH connector.


b.

Disconnect the T3*1 or O105*2 rear combination light assembly LH connector.

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door



Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.

HINT:

If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the rear turn signal light blink A
All LH side turn signal lights do not blink B



A

B

14.CHECK VEHICLE TYPE
14.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for TMC Made 5 Door without Mirror Heater A
for TMC Made 5 Door with Mirror Heater B
for TMMF Made 5 Door without Auto Retractor C
for TMMF Made 5 Door with Auto Retractor D




A

15.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

16.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

17.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

D

18.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
15.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L10-4 (B) - Body ground Always 10 kΩ or higher
T3-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L8-16 (B) - Body ground Always 10 kΩ or higher
T3-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L10-5 (B) - Body ground Always 10 kΩ or higher
O105-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 headlight assembly LH connector.


b.

Disconnect the L14 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (B) - Body ground Always 10 kΩ or higher
L14-10 (B) - Body ground Always 10 kΩ or higher
O105-1 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK LH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the A4 headlight assembly LH connector.


Procedure1

b.

Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.

HINT:

If the LH side turn signal lights other than the front turn signal light blink, the headlight assembly LH is malfunctioning.



Post-procedure1

c.

None


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



A

20.CHECK LH SIDE TURN SIGNAL LIGHTS (WIRE HARNESS)

B

21.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
20.CHECK LH SIDE TURN SIGNAL LIGHTS (WIRE HARNESS)
a.

Remove the headlight unit assembly LH from headlight assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY



b.

Connect the headlight assembly LH connector.


c.

Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.

HINT:

If all LH side turn signal lights do not blink, the wire harness LH is malfunctioning.



Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



A

B

21.CHECK LH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the headlight assembly LH connector.


b.

Disconnect the L10*1, L8*2 or L14*3 outer rear view mirror assembly LH connector.

*1: for TMC Made 5 Door without Mirror Heater or TMMF Made 5 Door without Auto Retractor

*2: for TMC Made 5 Door with Mirror Heater

*3: for 3 Door or TMMF 5 Door Made with Auto Retractor



Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If the LH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



A

22.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

B

23.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
22.CHECK LH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Remove the side turn signal light assembly LH from outer rear view mirror assembly LH.

for TMC Made: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMC Made)>REMOVAL

for TMMF Made: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMMF Made)>REMOVAL


b.

Connect the outer rear view mirror assembly LH connector.


Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the side turn signal light blink.

HINT:

If all LH side turn signal lights do not blink, the outer rear view mirror assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the side turn signal light blink A
All LH side turn signal lights do not blink B



A

B

23.CHECK LH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly LH connector.


b.

Disconnect the T3*1 or O105*2 rear combination light assembly LH connector.

*1: for TMC Made 5 Door

*2: for 3 Door or TMMF Made 5 Door



Procedure1

c.

Operate the turn signal switch and check that the LH side turn signal lights other than the rear turn signal light blink.

HINT:

If the LH side turn signal lights other than the rear turn signal light blink, the rear combination light assembly LH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
LH side turn signal lights other than the rear turn signal light blink A
All LH side turn signal lights do not blink B



A

B

24.CHECK VEHICLE TYPE
24.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for TMC Made 5 Door without Mirror Heater A
for TMC Made 5 Door with Mirror Heater B
for TMMF Made 5 Door without Auto Retractor C
for TMMF Made 5 Door with Auto Retractor D
for 3 Door E




A

25.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

26.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

27.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

D

28.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

E

29.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
25.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A4 headlight assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-6 (B) - Body ground Always 10 kΩ or higher
L10-4 (B) - Body ground Always 10 kΩ or higher
T3-2 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A4 headlight assembly LH connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-6 (B) - Body ground Always 10 kΩ or higher
L8-16 (B) - Body ground Always 10 kΩ or higher
T3-2 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A4 headlight assembly LH connector.


b.

Disconnect the L10 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-6 (B) - Body ground Always 10 kΩ or higher
L10-5 (B) - Body ground Always 10 kΩ or higher
O105-2 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A4 headlight assembly LH connector.


b.

Disconnect the L14 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-6 (B) - Body ground Always 10 kΩ or higher
L14-10 (B) - Body ground Always 10 kΩ or higher
O105-2 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (LH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A4 headlight assembly LH connector.


b.

Disconnect the L14 outer rear view mirror assembly LH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-6 (B) - Body ground Always 10 kΩ or higher
L14-1 (B) - Body ground Always 10 kΩ or higher
O105-2 (B) - Body ground Always 10 kΩ or higher
H7-1 (LL) - Body ground Always 10 kΩ or higher
H7-5 (TRNL) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Halogen Headlight A
for LED Headlight B




A

31.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

B

47.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)
31.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


Procedure1

b.

Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.

HINT:

If the RH side turn signal lights other than the front turn signal light blink, the headlight assembly RH is malfunctioning.



Post-procedure1

c.

None


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



A

B

32.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
32.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the headlight assembly RH connector.


b.

Disconnect the K10*1, K8*2 or K14*3 outer rear view mirror assembly RH connector.

*1: for TMC Made 5 Door without Mirror Heater or TMMF Made 5 Door without Auto Retractor

*2: for TMC Made 5 Door with Mirror Heater

*3: for TMMF Made 5 Door with Auto Retractor



Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



A

33.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

B

34.CHECK VEHICLE TYPE
33.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

Pre-procedure1

a.

Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.

for TMC Made: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMC Made)>REMOVAL

for TMMF Made: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMMF Made)>REMOVAL


b.

Connect the outer rear view mirror assembly RH connector.


Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



A

B

34.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for Rear Turn Signal Light Bulb Type A
for Rear Turn Signal Light LED Type B




A

35.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

B

41.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
35.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly RH connector.


b.

Disconnect the S1*1 or O102*2 rear combination light assembly RH connector.

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door



Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.

HINT:

If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the rear turn signal light blink A
All RH side turn signal lights do not blink B



A

B

36.CHECK VEHICLE TYPE
36.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for TMC Made 5 Door without Mirror Heater A
for TMC Made 5 Door with Mirror Heater B
for TMMF Made 5 Door without Auto Retractor C
for TMMF Made 5 Door with Auto Retractor D




A

37.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

38.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

39.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

D

40.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
37.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K10-4 (B) - Body ground Always 10 kΩ or higher
S1-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K8-16 (B) - Body ground Always 10 kΩ or higher
S1-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K10-5 (B) - Body ground Always 10 kΩ or higher
O102-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K14 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K14-10 (B) - Body ground Always 10 kΩ or higher
O102-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly RH connector.


b.

Disconnect the S3*1 or O106*2 rear combination light assembly RH connector.

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door



Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.

HINT:

If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the rear turn signal light blink A
All RH side turn signal lights do not blink B



A

B

42.CHECK VEHICLE TYPE
42.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for TMC Made 5 Door without Mirror Heater A
for TMC Made 5 Door with Mirror Heater B
for TMMF Made 5 Door without Auto Retractor C
for TMMF Made 5 Door with Auto Retractor D




A

43.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

44.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

45.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

D

46.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
43.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K10-4 (B) - Body ground Always 10 kΩ or higher
S3-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K8-16 (B) - Body ground Always 10 kΩ or higher
S3-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K10-5 (B) - Body ground Always 10 kΩ or higher
O106-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 headlight assembly RH connector.


b.

Disconnect the K14 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher
K14-10 (B) - Body ground Always 10 kΩ or higher
O106-1 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.CHECK RH SIDE TURN SIGNAL LIGHTS (FRONT TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Disconnect the A5 headlight assembly RH connector.


Procedure1

b.

Operate the turn signal switch and check that the RH side turn signal lights other than the front turn signal light blink.

HINT:

If the RH side turn signal lights other than the front turn signal light blink, the headlight assembly RH is malfunctioning.



Post-procedure1

c.

None


Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



A

48.CHECK RH SIDE TURN SIGNAL LIGHTS (WIRE HARNESS)

B

49.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)
48.CHECK RH SIDE TURN SIGNAL LIGHTS (WIRE HARNESS)
a.

Remove the headlight unit assembly RH from headlight assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY



b.

Connect the A5 headlight assembly RH connector.


c.

Operate the turn signal switch and check that the LH side turn signal lights other than the front turn signal light blink.

HINT:

If all LH side turn signal lights do not blink, the wire harness RH is malfunctioning.



Result:
Result Proceed to
LH side turn signal lights other than the front turn signal light blink A
All LH side turn signal lights do not blink B



A

B

49.CHECK RH SIDE TURN SIGNAL LIGHTS (SIDE TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the headlight assembly RH connector.


b.

Disconnect the K10*1, K8*2 or K14*3 outer rear view mirror assembly RH connector.

*1: for TMC Made 5 Door without Mirror Heater and TMMF Made 5 Door without Auto Retractor

*2: for TMC Made 5 Door with Mirror Heater

*3: for 3 Door TMMF Made 5 Door with Auto Retractor



Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If the RH side turn signal lights other than the side turn signal light blink, a component of the outer rear view mirror assembly RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



A

50.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

B

51.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)
50.CHECK RH SIDE TURN SIGNAL LIGHTS (OUTER REAR VIEW MIRROR ASSEMBLY RH)

Pre-procedure1

a.

Remove the side turn signal light assembly RH from outer rear view mirror assembly RH.

for TMC Made: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMC Made)>REMOVAL

for TMMF Made: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for TMMF Made)>REMOVAL


b.

Connect the K10 outer rear view mirror assembly RH connector.


Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the side turn signal light blink.

HINT:

If all RH side turn signal lights do not blink, the outer rear view mirror assembly RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the side turn signal light blink A
All RH side turn signal lights do not blink B



A

B

51.CHECK RH SIDE TURN SIGNAL LIGHTS (REAR TURN SIGNAL LIGHT CIRCUIT)

Pre-procedure1

a.

Connect the outer rear view mirror assembly RH connector.


b.

Disconnect the S3*1 or O106*2 rear combination light assembly RH connector.

*1: for TMC Made 5 Door

*2: for 3 Door or TMMF Made 5 Door



Procedure1

c.

Operate the turn signal switch and check that the RH side turn signal lights other than the rear turn signal light blink.

HINT:

If the RH side turn signal lights other than the rear turn signal light blink, the rear combination light cord RH is malfunctioning.



Post-procedure1

d.

None


Result:
Result Proceed to
RH side turn signal lights other than the rear turn signal light blink A
All RH side turn signal lights do not blink B



A

B

52.CHECK VEHICLE TYPE
52.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
for TMC Made 5 Door without Mirror Heater A
for TMC Made 5 Door with Mirror Heater B
for TMMF Made 5 Door without Auto Retractor C
for TMMF Made 5 Door with Auto Retractor D
for 3 Door E




A

53.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

B

54.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

C

55.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

D

56.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

E

57.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)
53.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A5 headlight assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-6 (B) - Body ground Always 10 kΩ or higher
K10-4 (B) - Body ground Always 10 kΩ or higher
S3-2 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

54.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A5 headlight assembly RH connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-6 (B) - Body ground Always 10 kΩ or higher
K8-16 (B) - Body ground Always 10 kΩ or higher
S3-2 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A5 headlight assembly RH connector.


b.

Disconnect the K10 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-6 (B) - Body ground Always 10 kΩ or higher
K10-5 (B) - Body ground Always 10 kΩ or higher
O106-2 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

56.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A5 headlight assembly RH connector.


b.

Disconnect the K14 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-6 (B) - Body ground Always 10 kΩ or higher
K14-10 (B) - Body ground Always 10 kΩ or higher
O106-2 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.CHECK HARNESS AND CONNECTOR (RH SIDE EACH PARTS - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the A5 headlight assembly RH connector.


b.

Disconnect the K14 outer rear view mirror assembly RH connector.


c.

Disconnect the H7 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-6 (B) - Body ground Always 10 kΩ or higher
K14-1 (B) - Body ground Always 10 kΩ or higher
O106-2 (B) - Body ground Always 10 kΩ or higher
H7-2 (LR) - Body ground Always 10 kΩ or higher
H7-6 (TRNR) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR