Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0448030 MANUAL TRANSAXLE SYSTEM C

EA67F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P071015  Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P071015.

Click hereDrivetrain>EA67F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>P071011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071015 Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open Manual transaxle oil temperature sensor (temperature sensor) output voltage exceeds 4.9 V (circuit open or shorted) for 5 seconds or more.
(1-trip detection logic
·

Wire harness or connector

·

Manual transaxle oil temperature sensor (temperature sensor)

·

ECM


Does not come on DTC stored SAE Code:
P0713

HINT:

When this DTC is output, check the manual transaxle oil temperature sensor (temperature sensor) in the Data List. Enter the following menus: Powertrain / Engine / Data List / M/T Oil Temperature.

DTC No. M/T Oil Temperature Malfunction
P071015 -40°C (-40°F)
·

Short to +B in THOM circuit

·

Open in THOM circuit

·

Open in THO circuit

·

Open in E2 circuit



If the Data List values are normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

Click hereDrivetrain>EA67F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


MONITOR DESCRIPTION

The ECM calculates the temperature of the MT fluid based on the voltage output by the manual transaxle oil temperature sensor (temperature sensor). If the output voltage of the manual transaxle oil temperature sensor (temperature sensor) is outside the normal range, there may be a malfunction in the manual transaxle oil temperature sensor (temperature sensor), or an open or short in the circuit. In that case, the ECM will illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Turn the ignition switch to ON and wait for 3 seconds or more.

4.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

5.

Input the DTC: P071015.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR))

Pre-procedure1

a.

Disconnect the D100 manual transaxle oil temperature sensor (temperature sensor) connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D100-1 (THO) - Body ground Ignition switch ON 0 to 5.5 V



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

NG

3.CHECK HARNESS AND CONNECTOR (MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR) - ECM)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.

Disconnect the D100 manual transaxle oil temperature sensor (temperature sensor) connector.


b.

Connect terminals 1 (THO) and 2 (E2) of the manual transaxle oil temperature sensor (temperature sensor) connector on the wire harness side.

C390248C02
5.448,0.521 5.792,0.781 0.344,0.26 6.125,2.042 5.75,1.417 true 5.031,2.063 5.469,1.438 true 1.104,1.927 1.417,2.125 0.313,0.198 10 false *1 2.813,1.927 3.125,2.125 0.313,0.198 10 false *2 1.427,1.073 2.042,1.271 0.615,0.198 10 false THO 1.521,1.365 1.833,1.563 0.313,0.198 10 false E2 2.563,1.063 3.177,1.26 0.615,0.198 10 false THOM 2.573,1.365 3.188,1.563 0.615,0.198 10 false ETHM 4.667,0.365 4.979,0.563 0.313,0.198 10 false *a 5.469,0.573 6.031,0.844 0.563,0.271 10 false D100 4.896,2.104 5.208,2.302 0.313,0.198 10 false THO 6.094,2.094 6.5,2.302 0.406,0.208 10 false E2
*1 Manual transaxle oil temperature sensor (Temperature Sensor) *2 ECM
*a Front view of wire harness connector
(to manual transaxle oil temperature sensor (Temperature Sensor))
- -



Procedure1

c.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
M/T Oil Temperature
50003 372 1301

Post-procedure1

d.

None.


Result:
Result Proceed to
The value of M/T Oil Temperature is higher than 135°C (275°F) OK
None of the above conditions are met NG



OK

REPLACE MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR) - ECM)

Pre-procedure1

a.

Disconnect the D100 manual transaxle oil temperature sensor (temperature sensor) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D100-1 (THO) - Body ground Ignition switch OFF Below 1 V



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR) - ECM)

4.CHECK HARNESS AND CONNECTOR (MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR) - ECM)

Pre-procedure1

a.

Disconnect the D104 ECM connector.


b.

Disconnect the D100 manual transaxle oil temperature sensor (temperature sensor) sensor connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D100-1 (THO) - D104-104 (THOM) Always Below 1 Ω
D100-2 (E2) - D104-126 (ETHM) Always Below 1 Ω
D100-2 (E2) or D104-126 (ETHM) - Other terminals Always 10 kΩ or higher



Post-procedure1

d.

Connect the D100 manual transaxle oil temperature sensor (temperature sensor) connector.


e.

Connect the D104 ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MANUAL TRANSAXLE OIL TEMPERATURE SENSOR (TEMPERATURE SENSOR) - ECM)