Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › TRANSFER OIL › from 2020.09
RM36W0E _52 Drivetrain _095692 GF1A TRANSFER / 4WD / AWD _0449392 TRANSFER OIL G

GF1A TRANSFER / 4WD / AWD  TRANSFER OIL  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·
C459759C01
1.656,1.427 1.656,0.969 true 1.583,1.438 1.771,1.625 0.188,0.188 10 true *a
*a NOT the Transfer Filler Plug


The plug shown in the illustration is not the transfer filler plug, so do not attempt to fill transfer oil via this plug.

·

Filling transfer oil via this plug will cause the transfer oil to be overfilled, resulting in oil leakage.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.CHECK TRANSFER OIL

a.

Stop the vehicle on a level surface.


b.
C447276

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


c.
C278961C01
2.667,0.854 2.979,1.052 0.313,0.198 10 false *a
*a 0 to 5.0 mm (0 to 0.197 in.)


Check that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the transfer filler plug hole.

If the result is not as specified, add transfer oil.

Oil grade:

Toyota genuine differential gear oil LT API GL-5 or equivalent


Viscosity:

SAE 75W-85


NOTICE:
·

Using transfer oil other than the specified oil may cause abnormal noise or vibration, or damage the transfer of your vehicle.

·

When adding oil, pour it slowly.

·

Too much or too little oil will lead to transfer problems.




d.

If the oil level is low, refill oil after checking for oil leaks.


e.
C446543C02
0.375,4.177 0.375,4.344 0.375,4.344 0.625,4.344 true 0.25,3.771 0.365,3.979 true 1,3.635 0.833,3.635 0.833,3.635 0.75,3.969 true 0.688,4.271 1,4.427 0.313,0.156 10 false *a 0.083,3.677 0.396,3.833 0.313,0.156 10 false *b 2.094,3.344 2.406,3.5 0.313,0.156 10 false *c 1.063,3.563 1.375,3.719 0.313,0.156 10 false SST
*a 10 mm Straight Hexagon Wrench
*b 10 mm Union Nut Wrench
*c Fulcrum Length


Using SST, 10 mm straight hexagon wrench and union nut wrench, install a new gasket into the transfer filler plug, and then install the transfer filler plug.

SST
09961-00950  

Torque:
Specified tightening torque : 39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + SST (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 19.9 N*m (203 kgf*cm, 15 ft.*lbf)




Hide 51410 3.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY