Home › General › MAINTENANCE › GF1A TRANSFER OIL › from 2020.09
RM36W0E _V1 General _088300 MAINTENANCE _0449398 GF1A TRANSFER OIL A

MAINTENANCE  GF1A TRANSFER OIL  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:
·
C459759C01
1.656,1.427 1.656,0.969 true 1.583,1.438 1.771,1.625 0.188,0.188 10 true *a
*a NOT the Transfer Filler Plug


The plug shown in the illustration is not the transfer filler plug, so do not attempt to fill transfer oil via this plug.

·

Filling transfer oil via this plug will cause the transfer oil to be overfilled, resulting in oil leakage.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN TRANSFER OIL

a.

Stop the vehicle on a level surface.


b.
C446542C02
1.281,0.417 1.74,0.542 true 1.021,1.083 1.552,1.052 true 1.063,0.333 1.292,0.542 0.229,0.208 10 true *1 0.802,1.021 1.031,1.229 0.229,0.208 10 true *2
*1 Transfer Filler Plug
*2 Transfer Drain Plug


Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


c.

Using a 10 mm hexagon socket wrench, remove the transfer drain plug and gasket and drain the transfer oil.


d.

Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 3.ADD TRANSFER OIL

a.

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


b.

Add transfer oil.

Oil grade:

Toyota genuine differential gear oil LT API GL-5 or equivalent


Viscosity:

SAE 75W-85


NOTICE:

Using transfer oil other than the specified oil may cause abnormal noise or vibration, or damage the transfer of your vehicle.



c.
C278961C01
2.667,0.854 2.979,1.052 0.313,0.198 10 false *a
*a 0 to 5.0 mm (0 to 0.197 in.)


Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the transfer filler plug hole.

NOTICE:
·

When adding oil, pour it slowly.

·

Add oil a little at a time, waiting several minutes between each addition of oil.

·

Too much or too little oil will lead to transfer problems.



Standard capacity:

0.40 to 0.50 liters (0.43 to 0.52 US qts, 0.36 to 0.44 Imp. qts)



d.

Wait approximately 5 minutes and check that the oil level has not changed.


e.
C446543C03
0.375,4.177 0.375,4.344 0.375,4.344 0.625,4.344 true 0.25,3.771 0.365,3.979 true 1,3.635 0.833,3.635 0.833,3.635 0.75,3.969 true 0.688,4.271 1,4.427 0.313,0.156 10 false *a 0.083,3.677 0.396,3.833 0.313,0.156 10 false *b 2.094,3.344 2.406,3.5 0.313,0.156 10 false *c 1.063,3.563 1.375,3.719 0.313,0.156 10 false SST
*a 10 mm Straight Hexagon Wrench
*b 10 mm Union Nut Wrench
*c Fulcrum Length


Using SST, 10 mm straight hexagon wrench and union nut wrench, install a new gasket into the transfer filler plug, and then install the transfer filler plug.

SST
09961-00950  

Torque:
Specified tightening torque : 39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + SST (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 19.9 N*m (203 kgf*cm, 15 ft.*lbf)




Hide 51410 4.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY