89221
1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Make sure that the connecting surfaces are free of foreign matter.
Do not touch the main body ECU (multiplex network body ECU) connector.
| *a | 20° or more |
| *b | Housing Sidewall |
|
Set in this Direction |
Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.
Make sure to keep the angle at 20° or more as shown in the illustration.
| *a | Housing Sidewall |
|
Slide in this Direction |
Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the guides.
| *a | Side A |
|
Install in this Direction |
While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.
Do not strike or apply excessive force to the side surface of the main body ECU (multiplex network body ECU).
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push Area |
Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).
Make sure to press only the push area.
Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.
If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.
82715
2.INSTALL WIRING HARNESS CLAMP BRACKET
Engage the guides to install the wiring harness clamp bracket to the instrument panel junction block assembly with multiplex network body ECU.
Temporarily install the bolt.
3.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU
| *a | Lock Lever |
Connect the connector.
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the claws.
Engage the claws.
Install the instrument panel junction block assembly with multiplex network body ECU with the bolt and 2 nuts.
Connect the 5 connectors.
for HV Model:
| *a | Lock Lever |
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
| *a | Lock Lever |
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the clamp.
Engage the clamp.
Connect the 5 connectors.
55308B
4.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
| *a | Bolt (A) |
| *b | Bolt (B) |
Install the No. 3 instrument panel to cowl brace sub-assembly with the 2 bolts and nut.
55480D
5.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
6.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for 1KR-FE:
Click hereGeneral>MAINTENANCE>1KR-FE AUXILIARY BATTERY>INSTALLATION
for M15A-FKS
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
for G16E-GTS:
Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>INSTALLATION
7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
8. ECU CONFIGURATION
If the main body ECU (multiplex network body ECU) has been replaced, perform ECU configuration.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>ECU CONFIGURATION