Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449593 TRANSMISSION CONTROL CABLE A

EA67F MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 33820B 5.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C450654C01
3.115,1.292 2.771,1.292 true 2.156,1.281 2.156,1.635 true 2.104,1.667 2.302,1.844 0.198,0.177 10 true *a 3.146,1.198 3.344,1.365 0.198,0.167 10 true *b
*a Transmission Control Select Cable
*b Transmission Control Shift Cable


Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.


b.

Disconnect the transmission control shift cable from the floor shift shift lever assembly.


c.
C450655

Using a screwdriver, pull out the stopper of the transmission control select cable.

NOTICE:

Do not remove the stopper. If it is removed, reinstall it to its original position.



d.
C450656

Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control select cable from the shift lever assembly.

NOTICE:
·

Do not rotate the nut excessively as the internal spring may jump out and the transmission control cable assembly will not be reusable.

·

Do not forcibly pull the transmission control cable assembly into the cabin.




e.

Disconnect the transmission control shift cable from the floor shift lever assembly in the same manner as the transmission control select cable.


f.
C450657N01
1.635,0.156 1.792,0.354 0.156,0.198 10 true B 0.771,0.583 0.927,0.781 0.156,0.198 10 true B 2.052,1.229 2.208,1.427 0.156,0.198 10 true A 2.458,1.51 2.615,1.708 0.156,0.198 10 true A

Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.


g.

Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.


h.
C450658

Remove the nut.


i.

Remove the 2 bolts and transmission control cable assembly from the vehicle body.