Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447813 ENGINE ASSEMBLY A

G16E-GTS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of engine assembly

·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front wheel alignment adjustment Calibration
·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.REMOVE FRONT WHEELS

Hide 51410 7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51441C 8.REMOVE ENGINE UNDER COVER RH

Hide 51442C 9.INSTALL ENGINE UNDER COVER LH

Hide 51447D 10.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

Hide 14.DRAIN ENGINE COOLANT

Hide 15.DRAIN MANUAL TRANSAXLE OIL

Hide 12601B 16.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A479678

Disengage the 4 clamps and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 17.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 18.REMOVE NO. 1 FRONT VENTILATOR SEAL (for LHD)

Hide 55815E 19.REMOVE NO. 1 FRONT VENTILATOR SEAL (for RHD)

Hide 55734A 20.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55735A 21.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 55701J 22.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 23.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 24.REMOVE AIR CLEANER ASSEMBLY

a.
A479679

Disconnect the vacuum switching valve connector.


b.

Disengage the clamp from the air cleaner cap sub-assembly.


c.
A479680

Disconnect the mass air flow meter connector.


d.

Disengage the clamp from the air cleaner cap sub-assembly.


e.
A479681

Remove the 2 clips.


f.
A479682

Disconnect the vacuum transmitting hose.


g.

Disengage the clamp from the intake air pipe.


h.

Disconnect the vacuum hose assy.


i.

Loosen the hose clamp.


j.

Remove the air cleaner assembly.


Hide 17771A 25.REMOVE AIR CLEANER BRACKET

a.
A479683

Disengage the clamp from the air cleaner bracket.


b.

Remove the 2 bolts and air cleaner bracket from the vehicle.


Hide 82662A 26.REMOVE NO. 1 RELAY BLOCK COVER

a.
A479684

Remove the 3 claws and No. 1 relay block cover from the engine room relay block.


Hide 82672 27.REMOVE JUNKTION BLOCK COVER

a.
A479685

Remove the junktion block cover.


Hide 28.DISCONNECT WIRE HARNESS

a.
A479686

Disengage the clamp to separate the engine wire from the vehicle.


b.

Remove the 2 bolts to separate the engine wire from the vehicle.


c.
A479687

Disengage the clamp to separate the engine wire from the vehicle.


d.
A479688

Remove the 2 nuts.


e.

Disconnect the 3 connectors from the engine room relay block.


f.

Disengage the 2 claws to separate the engine wire from the engine room relay block.


Hide 16571C 29.DISCONNECT NO. 1 RADIATOR HOSE

a.
A479689

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 30.DISCONNECT NO. 2 RADIATOR HOSE

a.
A479690

Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly.


Hide 17362B 31.REMOVE NO. 2 AIR TUBE

a.
A479691

Loosen the 2 hose clamps.


b.

Remove the bolt and remove the No. 2 air tube.


Hide 33820B 33.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A481177

Remove the 2 clips A to disconnect the transmission control cable assembly from the manual transaxle assembly.


b.

Remove the 2 clips B to disconnect the transmission control cable assembly from control cable bracket assembly.


Hide 44774E 34.DISCONNECT UNION TO CONNECTOR TUBE HOSE

Hide 16261G 35.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A479692

Slide the clip and disconnect the No. 1 water by-pass hose from the No. 4 water by-pass pipe.


Hide 16264 36.REMOVE NO. 2 WATER BY-PASS HOSE

a.
A479693

Slide the clip and disconnect the No. 2 water by-pass hose from the No. 4 water by-pass pipe.


Hide 23829A 37.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A479694

Slide the clip and disconnect the No. 1 fuel vapor hose from the fuel tank to canister tube.


Hide 16290F 38.DISCONNECT NO.3 WATER BY-PASS HOSE ASSEMBLY

Hide 87245 39.DISCONNECT INLET HEATER WATER HOSE

Hide 23901 40.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A479695

Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.


b.
A479696

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 88704 41.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 42.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 45259A 44.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 45.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 45260 46.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 31481A 48.DISCONNECT NO. 1 CLUTCH HOSE

a.
A458194

Using a 10 mm union nut wrench, disconnect the bleeder clutch release tube from the No. 1 clutch hose.


b.

Remove the clip and disconnect the No. 1 clutch hose from the clutch flexible hose bracket.


Hide 17361J 49.REMOVE NO. 1 AIR TUBE

a.
A479697

Remove tha 2 bolts.


b.

Lossen the 2 hose clamps and remove the No. 1 air tube.


Hide 50.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A479698

Remove the 3 bolts and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A479699

Remove the 4 bolts and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


d.
A479700

Remove the 8 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


e.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 51.INSTALL ENGINE HANGERS

a.
A479701C01
0.344,0.969 0.688,0.969 true 2.146,0.979 2.49,0.979 true 0.135,0.896 0.448,1.052 0.313,0.156 10 false *1 1.906,0.896 2.146,1.094 0.24,0.198 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
12281-25040
No. 2 Engine Hanger 12282-18010
12282-18020
Bolt 91552-F1045
91552-F1060



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 52.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A479702

Disengage the clamp from the engine mounting insulator LH.


b.
A479703

Remove the 5 bolts, nut and engine mounting insulator LH from the vehicle.


Hide 164A2 53.REMOVE RESERVE TANK ASSEMBLY

a.
A479704

Slide the clip and remove the No.3 water by-pass hose from the reserve tank assy.


b.

Disengage the clamp and remove the engine wire from the reserve tank assy.


c.

Remove the 2 bolts and remove the reserve tank assy from the vehicle.


Hide 12305 54.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A479705

Remove the clamp and disconnect the air conditioner tube.


b.
A479706

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 23826 55.REMOVE NO. 1 FUEL VAPOR FEED HOSE

a.
A479707

Disengage the 2 clamps from the engine assembly with transaxle.


b.

Slide the clip and remove the No. 1 fuel vapor feed hose from the engine assembly with transaxle.


Hide 28100 56.REMOVE STARTER ASSEMBLY

Hide 11363A 57.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A479708

Remove the flywheel housing side cover from the cylinder block sub-assembly.


Hide 16361A 58.REMOVE FAN AND GENERATOR V BELT

Hide 16620D 59.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A479709

Remove the 2 bolts and V-ribbed belt tensioner assembly from the timing chain cover assembly.


Hide 27020 60.REMOVE GENERATOR WITH REGULATOR ASSEMBLY

Hide 82121 61.REMOVE ENGINE WIRE

a.
A479710

Remove the 4 bolts.


b.
A479711

Remove the 4 bolts.


c.

Remove the 2 bolts.


d.
A479712

Remove the 2 bolts.


e.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 25051 62.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 37117B 63.REMOVE PROPELLER SHAFT HEAT INSULATOR

Hide 31001 65.REMOVE COVER AND DISC CLUTCH SET

Hide 19315 67.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 68.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 69.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.