Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for RHD) › 2020.09–2021.04
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0432677 AIR CONDITIONING UNIT(for RHD) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
No. 1 air conditioning radiator damper servo sub-assembly Initialize servo motor (Air Conditioning System) DTCs are stored for HV Model:
(Click here)
for Gasoline Model:
(Click here)
Air conditioning amplifier assembly
w/ Stop and Start System:
1.

Reset air conditioning information

2.

Learning of air conditioning information


Engine start function (Click here)
Initialize servo motor (Air Conditioning System) DTCs are stored for HV Model:
(Click here)
for Gasoline Model:
(Click here)

PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 51451A 2.REMOVE CENTER ENGINE UNDER COVER (except G16E-GTS)

Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for G16E-GTS)

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55735A 6.REMOVE WATER GUARD PLATE LH

a.
I116308

Disengage the claws to remove the water guard plate LH.


Hide 55815E 7.REMOVE NO. 1 FRONT VENTILATOR SEAL

a.
I116309

Disengage the claws to remove the No. 1 front ventilator seal.


Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
I116310

Disengage the clamp.


b.

for Cold Area Specification Vehicles:

i.
I116674

Disengage the clamps.


ii.

Disconnect the connector.



c.

Remove the 12 bolts and outer cowl top panel sub-assembly.

I116311


Hide 55225 9.REMOVE DASH PANEL HEAT INSULATOR (for G16E-GTS)

Hide 88707 10.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1KR-FE, G16E-GTS)

Hide 88716A 11.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (except 1KR-FE, G16E-GTS)

Hide 88710E 12.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE, G16E-GTS)

Hide 16290F 13.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 87245 14.DISCONNECT INLET HEATER WATER HOSE

Hide 87211 16.REMOVE NO. 1 AIR DUCT

a.
I116312

Remove the 2 bolts.


b.

Disengage the claws to remove the No. 1 air duct.


Hide 17.REMOVE STEERING COLUMN ASSEMBLY

Hide 55086A 18.REMOVE CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I115666

Remove the clip.


b.

Disengage the clamp to remove the center heater to register duct sub-assembly.


Hide 55084E 19.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116313

Remove the clip.


b.

Disengage the clamp to remove the No. 1 heater to register duct sub-assembly.


Hide 55085 20.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116314

Remove the clip.


b.

Disengage the clamp to remove the No. 2 heater to register duct sub-assembly.


Hide 21.REMOVE FRONT SEAT ASSEMBLY LH

Hide 22.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 58569D 23.REMOVE FRONT FLOOR CAUTION PLATE COVER (for Cold Area Specification Vehicles)

a.
I115777

Disengage the claw and guide to remove the front floor caution plate cover.


Hide 77306 24.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 25.REMOVE NO. 5 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 26.REMOVE NO. 3 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 58510D 27.SEPARATE FRONT FLOOR CARPET ASSEMBLY (for Cold Area Specification Vehicles)

a.

Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.

I116399


Hide 28.REMOVE NO. 4 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 29.REMOVE NO. 2 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 30.REMOVE NO. 1 REAR AIR DUCT (for Cold Area Specification Vehicles)

Hide 58510D 31.SEPARATE FRONT FLOOR CARPET ASSEMBLY (except Cold Area Specification Vehicles)

a.

Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.

I116315


Hide 55216C 32.REMOVE NO. 4 DASH PANEL INSULATOR PAD

a.

Cut each claw of the 2 clips and remove the No. 4 dash panel insulator pad.

I117105C01
4.719,1.135 4.875,1.344 4.875,1.344 5.01,1.125 false 4.792,1.354 5.104,1.552 0.313,0.198 10 false *a
*a Cut - -


NOTICE:

If the No. 4 dash panel insulator pad is damaged, replace it with a new one.



b.

Remove the 2 clips.


Hide 88539J 33.DISCONNECT DRAIN COOLER HOSE

a.
I115675

Disconnect the drain cooler hose.


Hide 88539G 34.REMOVE COOLER UNIT DRAIN HOSE GROMMET

a.
I117106

Remove the cooler unit drain hose grommet.

NOTICE:

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.



Hide 83108 35.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 55308B 36.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for TFTM Made)

a.
I115838

Remove the bolt and nut, No. 3 instrument panel to cowl brace sub-assembly.


Hide 37.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 38.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver)

Hide 55306A 39.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
I115676C02
1.917,1.792 2.188,2.01 0.271,0.219 12 true *A
*A for Cold Area Specification Vehicles


Remove the bolt to disconnect the wire harness.


b.

Disengage the clamps to disconnect the wire harness.


c.

for Cold Area Specification Vehicles:

i.

Remove the ground wire bolt.


ii.

Disengage the guide to disconnect the ground wire.



d.

Remove the bolt, screw, nut and No.1 instrument panel brace sub-assembly.


Hide 82141 40.SEPARATE INSTRUMENT PANEL WIRE

a.
I115677

Disengage the clamps.


b.
I115680

Remove the 2 nuts to separate the instrument panel junction block assembly RH.


c.

for Manual Air Conditioning System Single Layer Type:

i.
I115683

Disconnect the 2 connectors.


ii.

Disengage the clamp.



d.

for Manual Air Conditioning System Double Layer Type:

i.
I115684

Disconnect the 3 connectors.


ii.

Disengage the clamps.



e.

for Automatic Air Conditioning System:

i.
I115682

Disconnect the connector.


ii.

Disengage the clamp.



f.

for Manual Air Conditioning System:

i.
I115686

Disconnect the connector.


ii.

Disengage the clamp.



g.

for Automatic Air Conditioning System:

i.
I116396

Disconnect the 2 connectors.


ii.

Disengage the clamp.



h.

Disconnect each connector.

I115687C01
0.74,4.365 1,4.583 0.26,0.219 12 true *A 1.552,0.26 1.76,0.469 0.208,0.208 10 true *a 0.979,0.688 1.188,0.896 0.208,0.208 10 true *a 6.74,0.865 6.948,1.073 0.208,0.208 10 true *a 6.813,1.188 7.021,1.396 0.208,0.208 10 true *a 3.167,0.323 3.375,0.531 0.208,0.208 10 true *b 3.229,1.01 3.438,1.219 0.208,0.208 10 true *b 3.344,0.708 3.552,0.917 0.208,0.208 10 true *b 4.115,0.698 4.323,0.906 0.208,0.208 10 true *b 4.115,0.333 4.323,0.542 0.208,0.208 10 true *b 2.792,3.135 3,3.344 0.208,0.208 10 true *b 4.479,2.781 4.688,2.99 0.208,0.208 10 true *b 5.083,2.708 5.292,2.917 0.208,0.208 10 true *b 5.219,2.99 5.427,3.198 0.208,0.208 10 true *b 6.479,2.646 6.688,2.854 0.208,0.208 10 true *b 5.802,2.74 6.01,2.948 0.208,0.208 10 true *b 5.667,0.563 5.875,0.771 0.208,0.208 10 true *b
*A for Cold Area Specification Vehicles - -
*a Guide *b Clamp



i.

for Cold Area Specification Vehicles:

i.

Disconnect the connector.



j.

Remove the 4 ground wire bolts.


k.

Disengage the guides to disconnect the 4 ground wires.


l.

Disengage each clamp to separate the instrument panel wire.


Hide 41.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the nut and 6 bolts.

I116826


b.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


Hide 42.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly.

I116827