Home › General › MAINTENANCE › G16E-GTS COOLANT › from 2020.09
RM36W0E _V1 General _088300 MAINTENANCE _0449897 G16E-GTS COOLANT A

MAINTENANCE  G16E-GTS COOLANT  REPLACEMENT  


PROCEDURE

Hide 51410 1.SEPARATE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN ENGINE COOLANT

CAUTION:
·

When engine coolant is hot, do not remove the reserve tank cap or the radiator drain cock plug.

·

Fluid and steam may spray out due to high pressure, possibly resulting in burns.

A473346C01
6.073,3.292 6.438,3.292 true 5.938,1.292 5.938,1.635 true 5.833,1.667 6.042,1.844 0.208,0.177 10 true *1 6.49,3.198 6.698,3.375 0.208,0.177 10 true *2
*1 Reserve Tank Cap *2 Radiator Drain Cock Plug




a.
A473347C01
0.844,1.635 1.323,1.635 true 1.375,1.542 1.583,1.74 0.208,0.198 10 true *a
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.

Loosen the radiator drain cock plug.


c.
A473348C01
1.521,0.167 1.875,0.167 false 1.75,1.958 2.531,1.958 false 1.917,0.094 2.188,0.281 0.271,0.188 10 false *1 2.594,1.885 2.844,2.073 0.25,0.188 10 false *2
*1 Reserve Tank Cap
*2 Radiator Drain Cock Plug


Remove the reserve tank cap. Then drain the engine coolant.

HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD ENGINE COOLANT

a.
A390663C02
1.552,2.563 1.958,2.563 true 2.063,0.906 2.313,0.5 true 2.385,0.406 2.552,0.573 0.167,0.167 10 true *a 1.99,2.469 2.271,2.677 0.281,0.208 10 true *a
*a Air Release Valve


Using a 6 mm hexagon socket wrench, remove the air release valve from the radiator reserve tank assembly.


b.
A473349

Add engine coolant to the level shown in the illustration.

Standard Capacity:

5.2 liters (5.5 US qts, 4.6 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



c.

Using a 6 mm hexagon socket wrench, install the air release valve to the radiator reserve tank assembly.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


d.

Install the reserve tank cap.

NOTICE:

Securely tighten the reserve tank cap as much as possible.



e.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off.

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.

Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

HINT:

The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.



ii.

After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)


iii.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.

CAUTION:

When squeezing the No. 1 radiator hose and No. 2 radiator hose:

·

Wear protective gloves.

·

Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.

·

Keep your hands away from the fan.



NOTICE:
·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

Make sure that the radiator reserve tank assembly still has some engine coolant in it.

·

If the radiator reserve tank assembly does not have enough engine coolant, the engine may overheat or be seriously damaged.

·

If the radiator reserve tank assembly does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the radiator reserve tank assembly is filled to the FULL line.



HINT:

If the flowing sound of engine coolant can still be heard after bleeding air, perform the following procedure to bleed air again.

1.

Warm up the engine. (With the engine idling, check that the engine coolant is flowing into the radiator reserve tank assembly.)

2.

Run the engine at 2000 rpm for 2 minutes or more. (A)

3.

Leave the engine idling for 2 minutes or more. (B)

4.

Repeat steps (A) and (B) 4 times or more.





f.
A473344C02
1.406,1.323 2.74,0.75 2.74,0.75 2.906,0.75 true 1.438,1.479 2.563,1.74 2.563,1.74 2.729,1.74 true 2.99,0.688 3.302,0.844 0.313,0.156 10 false *a 2.802,1.667 3.115,1.823 0.313,0.156 10 false *b
*a MAX Line
*b MIN Line


After the engine has cooled down, check that the engine coolant level is between the MAX and MIN lines.

NOTICE:

The engine coolant levels in the compartments inside the radiator reserve tank assembly may differ, but this is not a malfunction.


If the engine coolant level is below the MIN line, add engine coolant to the MAX line.


Hide 51410 5.INSTALL ENGINE UNDER COVER ASSEMBLY NO.1