Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › ACTIVE TORQUE SPLIT AWD SYSTEM › from 2020.09
RM36W0E _52 Drivetrain _095692 GF1A TRANSFER / 4WD / AWD _0449992 ACTIVE TORQUE SPLIT AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  ACTIVE TORQUE SPLIT AWD SYSTEM  C11411C  4WD/AWD Range Actuator Temperature Sensor Circuit Range/Performance Circuit Voltage Out of Range  


DESCRIPTION

When a malfunction has occurred in the 4WD coupling solenoid system, the 4WD ECU assembly stores DTC C11411C.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
C11411C 4WD/AWD Range Actuator Temperature Sensor Circuit Range/Performance Circuit Voltage Out of Range
·

Even though it can be inferred from the driving conditions that the coupling is generating a significant amount of heat, the temperature sensor value is approximately -10°C (14°F) for 1 second or more, and this continues despite the ignition switch being turned off and then ON again 2 times

·

Even though the engine coolant temperature received from the ECM is less than 35°C (95°F), the temperature sensor value is fixed at 155°C (311°F) (short circuit condition), and this continues despite the ignition switch being turned off and then ON again 2 times

·

The temperature sensor power source voltage is 0.2 V or less for 1 second or more

·

The temperature sensor signal circuit voltage is 4.5 V or more for 1 second or more

·

The temperature sensor signal circuit voltage 1 is 2.1 V or less and voltage 2 is 0.2 V or less for 3 seconds or more


·

Wire harness or connector

·

Temperature sensor

·

4WD ECU assembly


Displayed Yes

DTC Detection Conditions: C11411C
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition The calorific value of the rear differential carrier assembly estimated from driving conditions is high enough ○ - - - -
The engine coolant temperature received from the ECM is below 35°C (95°F) - ○ - - -
Malfunction Status Temperature sensor is approximately -10°C (14°F) ○ - - - -
Temperature sensor temperature is stuck at approximately 155°C (311°F) or more (short circuit condition) - ○ - - -
The temperature sensor power source voltage is 0.2 V or less - - ○ - -
The temperature sensor signal circuit voltage is 4.5 V or higher - - - ○ -
The temperature sensor signal circuit voltage 1 is 2.1 V or less and voltage 2 is 0.2 V or less - - - - ○
Detection Time 1 second or more - 1 second or more 1 second or more 3 seconds or more
Number of Trips 2 trip 2 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C449048E01
4.99,1.396 5.594,1.594 0.604,0.198 10 false T1H 2.979,2.01 3.333,2.208 0.354,0.198 10 false CTS- 4.99,2.167 5.594,2.365 0.604,0.198 10 false T1L 1.948,2.802 3.365,3.021 1.417,0.219 10 false Temperature Sensor 1.948,2.625 2.552,2.823 0.604,0.198 10 false U3 5.271,3.188 5.667,3.385 0.396,0.198 10 false O119 5.281,3.354 6.698,3.573 1.417,0.219 10 false 4WD ECU Assembly 4.698,1.25 4.927,1.438 0.229,0.188 10 false 13 4.708,2.01 4.938,2.208 0.229,0.198 10 false 21 3.427,2.01 3.74,2.208 0.313,0.198 10 false 4 1.563,2 1.708,2.219 0.146,0.219 10 false 3 1.74,2.01 2.146,2.198 0.406,0.188 10 false CTS+

CAUTION / NOTICE / HINT

NOTICE:
·

When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>ACTIVE TORQUE SPLIT AWD SYSTEM>CALIBRATION

·

After performing repairs, clear the DTCs and check that the DTCs are not output again.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>ACTIVE TORQUE SPLIT AWD SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TEMPERATURE SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - TEMPERATURE SENSOR)

NG

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - TEMPERATURE SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the O119 4WD ECU assembly connector.


c.

Disconnect the U3 temperature sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O119-13 (T1H) - U3-3 (CTS+) Always Below 1 Ω
O119-21 (T1L) - U3-4 (CTS-) Always Below 1 Ω
O119-13 (T1H) or U3-3 (CTS+) - Body ground and other terminals Always 10 kΩ or higher
O119-21 (T1L) or U3-4 (CTS-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR